Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Search found 9 matches

by Squidous
Wed Jan 31, 2007 6:00 pm
Forum: Rover
Topic: TD5 Disco - What to look for.
Replies: 13
Views: 848

I have spoken to both Graeme Cooper and Bruce Davis Re: the chip. I think I will go with Bruce Davis, a couple of reasons; cost, instillation time, power output, has the chips on hand and he is a landy specialist. I am not familiar with a number of terms that have been used. CDL actuator ETG gauge ...
by Squidous
Tue Jan 23, 2007 6:01 pm
Forum: Rover
Topic: TD5 Disco - What to look for.
Replies: 13
Views: 848

Thanks for the info, I’ll call Graeme Cooper in Sydney and listen to what they have to say on the subject.
by Squidous
Mon Jan 22, 2007 7:27 pm
Forum: Rover
Topic: TD5 Disco - What to look for.
Replies: 13
Views: 848

RangingRover, I have just brought a 03 model TD5 Disco the vehicle is absolutely stock standard. I currently tow an off road camper trailer which will be upgraded to an off road caravan ; I am looking at a chip upgrade. Do you have a recommendation as which would suit the Disco best and any ...
by Squidous
Thu Jun 08, 2006 9:42 pm
Forum: Mitsubishi
Topic: NL turbo
Replies: 16
Views: 1318

Thanks for the input James; I think I’ll leave as it is now set. The proof will be in the towing, I’ll take the trailer out for a drag over the long weekend and see how the vehicle pulls.

Lawrie
by Squidous
Wed Jun 07, 2006 8:06 pm
Forum: Mitsubishi
Topic: NL turbo
Replies: 16
Views: 1318

6G74, Thanks for the info. I've used a small piece of brass rod which I have drilled a 1mm hole, the gauge is showing 10psi boost. Can't seem to get it over 10psi. However, saying that the turbo boost up to 10 psi very quickly and holds it, also has more pulling ability i.e.; accelerating in 5th ...
by Squidous
Sat Jun 03, 2006 11:34 am
Forum: Mitsubishi
Topic: NL turbo
Replies: 16
Views: 1318

Ok, I have now fitted a boost gauge in the line between the turbo and waste gate. The gauge shows a reading of 9.5-10psi, is there a way that I am able to adjust the boost without having to either adding a manual boost control or taking it to a diesel specialist. I really only want to have the boost ...
by Squidous
Mon May 29, 2006 10:24 pm
Forum: Mitsubishi
Topic: NL turbo
Replies: 16
Views: 1318

Thanks for the info, I'll get around to fitting a guage in the next couple of weeks.
by Squidous
Sun May 21, 2006 7:50 am
Forum: Mitsubishi
Topic: NL turbo
Replies: 16
Views: 1318

HotFourOk, Thanks for the info. I have a couple of other questions, if I measure the boost at the inlet manifold at the recommended psi (13.77psi) will that mean an increase in the psi at the turbo ( I have the 2.8 ICTD - 4M40 engine). Will that cause a problem for the turbo? Will there be an ...
by Squidous
Sat May 20, 2006 3:12 pm
Forum: Mitsubishi
Topic: NL turbo
Replies: 16
Views: 1318

Look at doing the same thing. I know where and how to fit the manual boost adjuster, not sure where to fit the boost guage. There are 2 lines coming from the turbo, one going to the waste gate and the other to the fuel pump, is one of these lines where I would fit to measure the boost? I have been ...