Outer Limits 4x4 Board

They did a have a problem with camshaft float (north/south) and there was a official Landrover fix.

From what I remember from TAFE, lpg was very abrasive/dry, and the gas didnt mix well with a/c oils, ie the gas would not pick the oil up to lubrcate the compressor etc. We tried it and was really cold heaps better than r134a. Filling the system with lpg may require a workcover certificate/+plate ...

How long was it after the rebuild, and did they romove and refit the box.

VSI 15 on the RTA website (is for unrestricted signatories) has been pulled by the RTA at the moment as they they are removing some engineering signatories for various reasons, there is still a list of restricted signatories available on the RTA site. Both engineers mentioned are on the unrestricted ...

The reason it doesnt make a noise in fourth is because in fourth the whole input main shaft is locked up like one big shaft form engine to transfer. The throw out would be making a noise no matter what gear it was in. It is most probably cluster gears ( 1st 2nd 3rd )or bearings on cluster. G52 drop ...

Seen this a couple times over the years just after replacing pads and it was either the load valve in the rear or a T valve or piece some where in the line, Changing pressure in the system while replacing pads seems to stuff it. Sorry cant be more descriptive as one the other boys did the work. They ...

I have not worked on 100 crusier for years, but do they have that stupid immobilser box covering the back of the pump where the fuel cut solenoid is, or am I thinking of someting else.

Some engineers sometimes interpret things the way they like for the prices they charge. Federal Acts overide State Acts (goto DOTARS). Police RTA and other State authorities are not focused on getting modified 4WD's off the road as we are only a miniority of road users who mainly use on weekends in ...

Federal and State Acts, allow for a 50mm increase in tyre diameter, for an 80's to be engineered "legally" it would have to have diffs fitted from a vehicle that orinally had tyres within 50mm of 44 inch tyres. just because it has an engineers certificate doesnt make it legal.

Motor in your lux should be a 3y for that year model, I got my power steering pump and bracket by going into the "find a part" website.

Could be lots of things being intermittent. Are you able to hold the revs up just off idle when it is doing it and then put it into drive. Could be lock up converter or may be a slow Idle solenoid motor not being able to react fast enough to load or it may get stuck, had similar problems with speed ...

LN & RN46 should have 4.8's with cause spline pinions depending on year model. YN60 should have 4.8's with fine spline pinion.

Sounds like someone cut and add a piece to the steering shaft. If there is no uni joint at the firewall which I dont think there was on that model you may have to get a new shaft or cut and shut the one that is on it.

PM the Professor, his is on ebay at this moment.

I have the dellows book and it has here a conversion for Commo V6 to Landcruiser 5 speed. Every conversion that I used a Dellows product there were problems. Marks dont do a kit for this, but they do a kit for Ford c4 and cruiser transfer. I was going to put xe Falcon 6 and c4 auto with marks ...

Hi steer conversion is when the steering or (ackerman arms) are replaced to move the Tie rod above the springs and put the drag link from the steering box to the lh steering arm East West as to the original North South arrngement. If you keep you leaf spring set up it doesnt change the way springs ...

You use to be able to purchase 1 litre bottles with a hose attached to the lid with the oil already in them and squeeze it in and keep filling it or get a big syringe (macnaught etc).

Input shaft bearing in gearbox is common problem in G52 box as I have 3 that need this repair I guess R151 may have similar problem. If making noise in every gear it has to be an input output transfer diff etc as these are spinning all the time and not engaged individually or loaded individually as ...