Outer Limits 4x4 Board

I have a Kempii pulse 2800 automotive. (3phase power.) Very easy to use. I always use it on "automatic" Just set the dial to the thickness of the material I am welding and the machine automatically sets the correct amps and wire feed speed. Makes me look like a pro anytime I have welded AL. I mainly ...

Well it is obvious the CCDA has no experience in building exo cages. So some one should start a new thread here and get some good input from everyone into building an exo cage to a minimum standard to protect the occupants, not the truck . Summarise it and submit it to the CCDA for a look. If you ...

Have you Checked your engine mounts Is one broken ??

Gear Box Factory 28 Queen St, Revesby Heights is OK for 4wd gearboxes.

91Mav wrote:So no one puts a tack on their inner axle inner spline any more?

I have never seen an axle failure from a Martac weld. The axle nearly always breaks at the slim part.

I would use a product from KBS coatings to stop rust in the tank. Aust. made and fast delivery also.
check there web out here

http://www.kbs-coatings.com.au/Tank-Sea ... 0-1-0.html

Could be a sticking thermostat.

Competition insurance covers you whilst within the competition confines Your vehicle insurance covers you whist traveling around the rest of site in same way as you are covered for an accident in a shopping center car park. jono4x4 The policy they require, I believe, is the simple 3rd party ...

I assume one harness only required for the driver as navi will be out of the vehicle at ALL times?

Is a 3 point harness sufficient?
.

Some of you blokes that want to compete in an unengineered, unregistered vehicle may have a pos that breaks and holds up the comp for the rest of the competitors and spectators. Or is it you want to compete in a rusty old wreck on its last legs with a few dodgy mods and with no money spent to keep ...

Can you add some clear fuel line to see where the air bubbles etc. are originating from?

Try the 4 longest leaves in the rear plus the 10mm?? thick flat overload leaf each side. I assume you will have no passengers in the rear.

Leave the front as is and see how it feels.

For comfort air down in the front to about 17psi and rears 2psi less.

Probably not worth doing it perfect as it is a tray.
Wire wheel on the end of the angle grinder works fast to get rust off.
I would also paint all the inside of the tray rather than touch up a few spots.
Use 2 pack paint it is a lot tougher than acrylic and easier to apply.

Ok I was sober at presentation and Steven Brennan driving and John John navigator won their class (Touring) in a Hilux shorty of course, with a total of 655 points which also gives them the over all win as well. 1st prize an ARB diff lock! Over $19000 in total prizes Well done to TLCC with a top ...

How is your engine immobilizer remote ? Does it need new batteries?

Go and get your own personal accident cover, that covers you 24 /7 for YOUR lifestyle and expenses.

If you cant afford to do that, dont crash!

.

One day you will want to sell your truck with a 4Y and guess what no one will want it.

If it had a reco 2L in it it would get a lot of interest and a higher price!

Heres a tip

Make sure you get him to send them separately to each persons address

If they all come to aussie in one box customs and Gst may be payable above a certain $$ amount.

With the leaky O rings you will know if yours fail because the oil level on the dip stick will rise due to diesel dilluting it.

PANIC get it repaired imediately as the engine may start running FULL THROTTLE, on the over full sump oil. Turning the key off will not shut the engine off!

Get some Exhaust pipe then fit the rubber hose to the ends.

It is easy to prime There is a pump probably on the fuel filter

pump this untill it goes hard Then crank it over normally.

When it starts, If it vibrates you have probably bent a con rod or 2.

meiamaro wrote:Would plasma style rope be suitable for private use/abuse or
is it better to stick with the wire supplied?
Ian.

in your case just stick with the wire supplied untill you damage it .

Just remove the two shortest 6mm leaves.. That is 4 leaves total.

Take it for a rough test drive and see what you think after a couple of weeks.

Well done to Becca and Dustin, Dustrin had that rig under control the whole time via Becca. :D Dustin is such a nice person to chat to as well. My observations for a buggy would be 1 Must be able to turn ( rear steer a big help) 2 Low CG to help on the crazy angles. 3 Strongly built to sustain huge ...

Tyre size is 36.5 same as last year.

Measured horizontally same as last year.

Most of the hi tec diesels oils these days are modified to stop glazing of the bores.

Read the label and choose an oil that is suitable for your application.

The c clamp around the spring pack is easy to open.
Get a chissel to start to lever the end up then grab the end with a pair of vice grips.

Have you done a spring over on the troopy?

nathan24 wrote:CAN I PUT A 2.8 IN A YN65?85 MOD ?OR 2.4 WHATEVER IS EASIEST IS ALL THE ELECTRICS THE SAME AS PETROL 3Y ?

No, electrics are different.
Desiel has glow plugs and timer
Tacho pick up will be different.

.

You sure the axle is bent and that the flange plate which sits over the wheel bearing is just not sitting square. You really need to set it up in a lathe and spin it and measure the run out along it lenght. I checked by stickong it on stands and in D. 1 wheel wobbles, swap wheels, wobble stays. The ...

Congratulations Pete Antunac all you had to do to win, is hold it all together long enough to beat the rest, and you did.

Well done to Sam Overton also for keeping the pressure on!
.