Outer Limits 4x4 Board

Hey guys havent been on board for some time... can someone tell me where i can find ryano i couldnt find him at 4by's anymore ??? Im after some wheels and tyres and hes the man

Patroldocta make custom airbox's and do a neat job
here is there highest flowing unit 4" opening

PIRTEC will source it for you

NB is 'PIPE' not 'tube' ... pipe is measured from inside... tube is outside

locktup 4x4

Its for an 85 hilux solid axle ... needing bearing and seal numbers for the front and rear axle so i can order through work...

Just wanted to make sure if i ordered a 37100 bearing it would be the same as a cb09

80's_delirious wrote:checkout the link below

Punch in your model here

Just had a look these numbers are different to the actual part numbers...

ex: center bearing number from repco cb09 ... on the website 37100 ???

booflux wrote:3rz best bang for buck, 1uz sounds better although the 3rz limiter is intoxicating

X2

i just ground mine back flush takes 5 min

And you will need longer shackles when retaining original position

check out the bible top of yota section

who did you order the kit through ?

Need part numbers for full front end rebuild including wheel bearings knuckle / kingpin bearings and seals

Running 37"s iroks with a 3rz motor so those who have run with either tyre diff ratio setups let me know your opinions?

Can get 5.1229's are these hiace centers ? if so are they stronger or weaker than 5.29s ?

troopymad wrote:

Z()LTAN wrote:i pay
$30 a side for wheel bearing kits incl all gaskets and seals
$90 for both side swivel rebuild kit

This is why i don't worry about running big offset rims and 3" wheel spacers

thats my theory too

X 3

anyone run 5.122 ... got a set for 37"s behind a 3rz was just wondering if they are stronger than 5.29's or weaker?

im pretty sure they are out of a hiace or similar

Why not just buy the stronger upgrade studs available from places like Locktup? http://locktup4x4.com.au/hilux-solid-front-78/steering-80/magnum-knuckle-studtm-heavy-duty-knuckle-studs-set-of-194.html Ahh because there $180 a set :shock: I ended up machining some up out of grade 8 ... just thought ...

In the process of upgrading my knuckle studs on my 85 hilux ... Changing the studs from 12mm to 14mm and need to know where to find the studs ... tried repco and couldnt help ... the studs are a 12mm course thread going into the housing and a 12mm fine holding the steering arm on top... so after the ...

want to do a ubolt flip up front (have hi steer) can anyone tell me u bolt sizes needed on my '85 model pickup?? will get sum made up. need to know dia's (round) and widths for square ones.

TURBOMQ wrote:where bouts can i get some bent up for a snorkle in melbourne because they want 400 bucks for one already made??

a cheaper way is to buy the rubber bends... i got mine from pirtec

Yes roll cage tube for my 4X4

Thanks guys

Anyone got a good cheap place to buy tube in melbourne ?

Locktup have them for $399 a pair free shipping

10" 12" or 14" sizes and great service

I know this has been discussed before but where can i buy a good tube bender from, in australia ?

http://locktup4x4.com.au/universal-118/ ... hocks-152/

say no more

locktup sell trail gear products therefore all made in the U.S

In saying that the lines are identical to the factory lines so i cant see any problem

Go through locktup4x4.com they are excellent quality and a very good price ... i got the pirtek bloke onsite at work to look around for prices and he reackons locktup are the cheapest going buy a long way

Iroks purchased thanks to Rhino at fourbys... 37" on 17" bead locks ...


UNBELIEVABLE PRICE ... RHINO YOUR THE BEST

Just measured up a 40 " trep on 17's today and measures up slightly under 40" very close but

any dimensions would be great ... and saves some cash

need at least 5 people keen to go

are the road compound radial or bias ply ?