Outer Limits 4x4 Board

Im wondering if someone could tell me if an air locker (arb) out of a bj73 mid wheel base landcruiser 1985 would fit into the rear of a 1994 4.2 litre 80 series. They both have the standard diffs that the factory put in them.
thanks rusty

I have a gq ute td42, on the side which the turbo sits theres quite a bit of crap mounted like the compressor, manifold and solinoids for diff locks, shower heat exchanger and the second battery.

Im just doing some research into weather I should buy a turbo blanket or cover to slip over the exhaust side of the turbo. I have two yellow top optima batteries and dont want to wreck them with excessive heat. Im looking at buying a high mount turbo and manifold from JDM performance, to which he ...

Ive got koni ajustable front and rear in my 80 series, and as luck has it there actually being sent off today to be rebuilt by: Toperformance No. 8 trade place vermont Vic Phone 0398731722 I talked to a fella called ian very helpful, ten day turn around on shockers being rebuilt and cost of $91.00 ...

My advice is dont use it in auto applications, all cabling in a vehicle should be multi strandard. Using solid conductor wiring ie shielded or unshielded twisted pair will only lead to fatigue at any joint or point of vibration and cause issues for you. There are plenty of other multicore stranded ...

Does anyone know the name of the company that does this?

Cheers Russ

thankyou for the replys, Cant find tube that size so Im going have to machine some ends up to fit the bushes. Unless someone has some stock panhards they dont want

Thanks
Rusty

Sorry my description is not that great. I dont mean the centre through the bush Im after the actual metal ring that houses the bush its internal measurement. I measured the outside of the metal ring and that seems to be approx 54mm.

Can anyone tell me the internal size of a gq panhard bush housing (the metal circle that the bush goes in on the chasis mount side).

Thanks
Rusty

Bought the panhards off a 2001 GU patrol but they dont fit. Apparently they changed one end of the panhard to a bigger size in the late GQ's. So I have one set of panhards that I cant use. Has anyone got a set of ones that will fit the early GQ's that I can swap for the GU ones. These were only on ...

I know engine mounted hydraulic pumps have been covered extensivly but has anyone mounted a hydraulic pump on a GQ patrol via the pto drive. Would love to know if you can do it and what parts fit. Any help would be greatly appreciated as I have all control gear and winch ready to go in.



Thanks

Love them looked on eBay as suggested but couldn't see the different types of lables such as bunny burners. Do they custom make lables?

Thanks for replies

Can anyone tell me where you can buy ARB type rocker switches at a reasonable price? Want to convert all old toggle switches into something that looks half decent.

Thanks

Sorry about that been a long morning I do mean panhards not thinking right.

Please help.
I am able to get a set of ajustable drag links both front and rear off a GU but Im unsure if they will fit on my 1992 GQ ute. Is there any truth that they will fit as long as the gu was manufactured before 2002.


Regards Rusty

Can someone enlighten me on the fors and againsts on a high or low mount manifold for a tubo on a td42. Is there any advantages of either.

Kind regards Rusty

There is no difference between uhf(477Mhz) and CB(27Mhz) cable they have an impedence rating of 50 ohms both the same size cable (assuming that it is a five watt unit). As to joining the co-ax cable you the best way to join them is with the proper male and female ends, both that you can find at any ...

Wondering if anyony can post up photos of their trays. Looking to build or aquire a tray for the GQ (if someone has one for sale).

Regards Russ

Im looking at turboing the gq at the moment so exhaust will be modified as above what type of pump are you running and do you have photos of your set up


Regards Russ

Thanks for the replies but I cant see where on the motor I can fit the clutch driven pump(even after reading runva thread) whilst keeping the aircon. This is why Im still interested in trying the pto option.

So still looking for info.

Regards Russ

Im wondering if anyone has played around with setting up a gq with a hydraulic pump off the pto? If so what pump has been used. Ive looked at some photos of g/box and pto, there does not appear to be much room to mount a pump or is there? I have everything except for the pto and pump to set up this ...

I know this should be in 'wanted' and Ive posted it there too but.....

Would anyone have a bench seat to suit a gq ute, cloth trim.

Regards Russ

0417 573077

Thanks for the info Ill have to keep an eye out for one, unless someone has one for sale.

Are you able to fit a pto to a 92 cab / chasis ute? If so how much would they go for and where would I start looking?

Has anyone played around with a pto and gear pump set up, would be interested to see or hear of those set ups too, the pros and cons.

Cheers Russ

Have a look on 3rdrock4x4 forum look under members rigs and look for scotto. Scott has built a 45 with coils and has photos.

Hope this helps

Cheers Russ

Ive had a boost guage on it it reads eight pound boost. If I put the right boot into it, you can feel the power and it wants to accelerate, but it dies off as if lifting the foot off the go peddal about two or three seconds after it does still accelerate but very slowly. It is very noticeable when I ...

No luck as yet to the problem at all had all that checked and seems to be fine, Id love to be able to solve this prob. Thanks for all the input as well its muchly appreciated.

Can anyone help me with a problem that I have with my 13bt diesel landcruiser motor? I have had the injector pump rebuilt completely, rebuilt and the turbo completely as well. However the car only wants to go hard for the first few seconds and then the power dies and excelerates slowly. I have ...

Can anyone post up some photos of how they modified their bars to suit a 50mm body lift. I dont want to reinvent the wheel just want something that works well.

Cheers Russ