Outer Limits 4x4 Board

looks good mate

awesome

hey mate, ive got a ute and a few short and mid wheel base ones. the front springs out of them all look the same. the rear in the ute runs a spring over setup which has different length leaves from what i can see than the sprung under rears of the mid and short wheelbase. the motors and boxes all ...

i read somewhere that you can clean up the pins with some fine sand paper and get the bearing to slip on with a minimum of interference. makes getting it off in the future much easier. and if you are changing the bearing you should set the preload again. i had to take mine on and off a few times to ...

that's good to hear, i have a spare front housing here with me that im going to replace the seal and bearing and take that up with me. so it should be all doable when i get up there then. the pressing/pulling of the parts made me grab the spare housing to fix up down here first, looks like that was ...

Hey guys i was wondering if anyone had changed the 80 series (part time, manual) front output seal while leaving the transfer still attached to the gearbox, I heard its pretty hard to do with the stock body height but would the 2in body lift make it possible to get to the two hard too reach bolts. I ...

hey guys thanks for the reply. i found out that the first yr of production 84-85 i think had a smaller flange pattern. and then everything else has the larger pattern. so i swapped on in off a f73 i have sitting around. cheers brenton

does anyone have a ute and can they measure the stud pattern for the transfer case rear output flange to see if its different to a swb or mwb flange. cheers

hey guys i managed to explode my output flange from my transfer case, it looks to be a custom made one. its in my f77 ute and the uni joints and diffs all have been swapped to 65x65 or maybe 66x66 flanges. has any one got some info where to get a new transfer case rear flange in the rocky spline ...

its coming along well, keep chipping away at it.

nice, good to hear

hey guys do feroza guards fit a rocky, ive got a early model rocky and im looking for some guards to cut up do feroza ones fit? cheers brenton

i think the mods have bought toyota's lol

yeah alot of good info in there, its hard to find good rocky or feroza info

hey mate, have you tried pulling the shifter out to have a look at it too make sure its all okay, then maybe you can have a look in through the top to see if anything obvious is wrong. ive never had this problem on a rocky but on a sierra i once had if the bushing was worn out then you couldnt get ...

just make sure anything you put near something that gets hot is not flammable otherwise it might catch alight and be very hard to put out. if you havent done the doors you might be getting some noise thru them, also are your engine mounts still good and also the gear box and the secondary mount on ...

hey guys i have a few rockys and i need to swap out a windscreen, ive got two rockys with cracked windscreens before i got them. not sure how it happened looks like body twist or something. is this common? and can i reuse the windsreen rubbers if i can manage to push out the windows and swap them ...

dude that sucks big time, if it still drives dont crush it, just keep driving or even make a tube body up.

hey mate did you try taking the head to a head shop and see if they can weld it up or fix it ? and wont a non turbo head (dl42) fit on as a replacement ?
cheers

hey mate i dont have any links on the daihatsu manual , but maybe you can use an old hilux one for the engine stuff sine they are very similar .

hey guys i have a f70 that had air con but the previous owner cut out the condesor and it seems the dryers setup and just left the compressor and parts in side the car. im looking at getting all this and fitting it into my f77. im looking for a condensor and dryer setup , does anyone know if the ...

hey mate the pump mounts down on the drivers side, ive had problems with brackets before. it mounts to the front of the block with two bolts, then the bracket runs down the block and picks up one or two of the bolts for the engine mount. i had a f73 that i had to cut the bracket down near the engine ...

thanks ill have to hit up my local brake place and check it out .
cheers

nice looking truck

hey guys are the rear brakes the same feroza to rocky , i have a rocky and want to swap in some new wheel cylinders. ive seen feroza one and rocky ones , the feroza ones are always listed cheaper. are they the same ?
cheers

hey mate did you end up trying to fit the hilux transfer ? any news

hey mate thats a good qs, we should be a sticky about what panels exchange etc. id like a set of late model rocky gaurds on my f77 , some one might some info for you. this forum is pretty dead atm :( , you could put up a few pics of your car to spark some interest maybe
cheers brenton

looking good , making good progress . is that an f77 in the background ?

have you done any more work on this truck ?

yeah i have a td aswell i didnt mind the non turbo , but once i went turbo prob wouldnt go back , im running 33x12.5 and have no problem sitting on 100 . plus the DL diesels sound so much better than the hilux 2.8 turbo . the DL sound just like big trucks when you run no muffler lol.