Outer Limits 4x4 Board

I have the mighty kong case holder and the 6.5 gears. I also have twin locked and run 31's I have broken many mounts before the mighty kong but not a one from when I installed the mighty kong. I do not treat my car easy its flat out or broken. i have done frazer island from sydney then went and did ...

correct me if i am wrong but i am sure that the 1.6 head willl fit all the 1.3 gear on it.... i do know for a fact that the headers are the same, so i would asume the same for the inlet

I have rebuilt my 1.3 and i am sure i have got about the most power you can get out of the little 1.3 without superchaging it. I did a cam regrind a weber far bit of porting headers and a good system. I also run 31s and 6.5 transfer gears. I do have a lot of power well for a zook, i can do perfect ...

you have knocked off the earth wires on the rear for sure also the coil wires
replace them it will start

You start non tech threads in the tech section and it goes for 5 pages :finger:
Nik


its to make us all better zook owners :roll:
make us more aware and to love our little babies
anyone can do it easy in a pootrol or a crusier, its not till you own the zook you get the full love for the hard ...

you can not get enough, and all you think about is getting in the bush and smashing it

mainly just a cheaper way of getting the bit over to aus.

but i need CVs
rear axle
stronger tailshaft rear

brendan_h wrote:when your missus has a miscarriage after riding in your zook.

thats sick

j-top paj wrote:

zook7177 wrote:

j-top paj wrote:when you and your navi put you over GVM

Or just myself
LOL

if your the one driving in your avatar?

yes, bigger and better

j-top paj wrote:when you and your navi put you over GVM

Or just myself
LOL

nicbeer wrote:

stumped wrote:... when you can tell the difference between a 1L, NT, WT, and coily at first glance

best thread ever

not only that is when u can tell the difference when someone picks up a driveshaft(any part) and u can pick it from what it comes from.

And tell most of the mods done to that zook

when you go on a 2 week trip to fraser island and have to put all your gear in a mates car

... You get asked "why do you have mud on the roof?" and just smile.

when you're clothes always match you're truck (muddy)

When you're lifted, locked, re-geared, and new shoe'd and your entire build up is still under $5000

When you know the best way to remove stuck large phillips head screws ...

YOU KNOW YOU OWN A REAL SUZUKI WHEN....

It's smaller than everything else on the trail

If you go to get the Sunday paper and come back on Monday without it

If you use a hose to clean the inside and the outside :D

If you own it outright

When the best route from A to B is through the mud ...

just looked under my car. drove home from fraser island the other no hellies only driving and uni has play in it. I am lifted but only 2" spring under, tried greasable and non no difference

hey man if you are going to use pvc make sure you use the high pressure pipe, 2 reasons, 1 much stronger can handle the knocks and 2 it is the correct size for the origial rubber bend that comes out of the air box

I keep blowing uni joints in the rear of my rear shaft one closest to the diff. Its a 89 serria with twin lockrites and low range gears, I have built the engine up to have torque and i run a webber. what can i do to stop blowing unis?????????????

My mates tell to stop doing hellies, but its fun

i have twin lockrites and 6.5 gears, I love it the zook is almost unstopable. the only thing i hate is the big clicks when turning in a car park ect. O and the very heavy steering

I am leaving on thursday to go to fraser island in my zook, I have replaced the drivers seat aswell as rebuilt the motor, 6.5 gears 31s made draws new brakes every thing that i could do i have done.
Massive trip for the zook, but easy and slow not to break anything

try doing an oil change and put some thicker oil in it will last a while longer.

well i all most lay it down twice and that was fun maybe that could have somethin to do with it

how can i tell if rings are shot ?? and what do i need to do to fix??

compression test.
my motor had oil in the air box, was so bad that the air cleaner would block up. so i got rid of the air ...

my little monster truck bar

yes MART it looks good but it does not look like toilet plumbing like mine, it has to have a bit of home made zook style. you even painted it blue to match the car, love it

I don't mean to bust in on this thread but has anyone got pics of DIY Sierra snorkels? There isn't too many pics left in the bible now. I'm wanting to do a 3" exhaust tube snorkel and I'm needing ideas for fixing to A pillar and joining to air box.

Sorry for busting in Reprise :oops:

Here is ...

does anyone get the "chatter" effect when they blip the throttle? Its like when it decelerates it sort of goes "clak clack clak" and kinda jerks when it slows down/decelerates (if you bounce or drop the accelorator quick enough)... Is it normal?

EDIT: i mean when i low range 1st btw..
i think ...

I know you have them on the zook, What are they who has the best one
Mine i got for xmass

$70US to get them over here isn't too bad considering the x-rate is better these days... I could imagine the AU shop prices wanting a lot more than getting them shipped from US yourself. Still either way, maybe not worth the effort

no not when i just got a price from an exhaust place near me for ...

how did you go with freight cost, and do you know if they will fit on the 1.6 carby motor

Calmini USA forwarded me their AUST distributor contacts:

http://www.4wdusa.com.au/

http://www.highcountrycustoms.com.au/

http://snakeracing.com.au/

I had a quick look at the sites (not that I hadn't ...

should do. 1.3 carby and 1.6 carby have rectangular ports. The EFI motors have round ports.

Vitara and sierra extractors have to follow a different line as the chassis widths and exhaust paths are different, but the heads themselves have the same bolt pattern.

Steve.


So if i bough these they ...

http://www.puresuzuki.com/header1.htm
Hope the link works , the header is up on the website and available now.
Sarge

Ohhh... why did you have to show me this now I want some!! LOL They look awesome + all the gear that goes with it is a much needed bonus. The bolt up bottom flange is something ...