Outer Limits 4x4 Board

Large offset or wheel spacers?

I coiled up some tube and chucked a filter on the end with the tube running into the chassis rail.

I've got a Safari snorkel to suit LN65 for sale. Couple of light scratches, thats all. PM for info etc.

Thanks ae86levin, I have read the 4wheelin.ca site and that was pretty good, that other one is awesome too cheers.

Is a boost compensator needed or is it a bit of a finer tuning thing?

Cheers, Stubbs

In effect, boost compensator's limit the fuel when off boost. Without one, the engine will run ...

Bolt in or can you weld?

This would be the first decision.

Shit, sorry buddy. Just checked now, low pressure is towards the rear of the car, the input shaft end.

http://www.outerlimits4x4.com/search.ph ... uthor=&fid" onclick="window.open(this.href);return false;[]=8&sc=1&sf=all&sr=posts&sk=t&sd=d&st=0&ch=300&t=0&submit=Search

I'll double check tonight if no-one else posts up before then.

ive had a look at trialgear website and i can get
rhd highsteer kit, u-bolt flip, power steering mount bracket, blistiens, and shock hoops for 516 bucks u.s thats about 570 aust
from locktup this would cost 1799 aus unless i went for the ruf kit which has procomp shocks which i dont want and ...

80 series.

What's towing capacity of the hilux? I would think it would be than a car trailer and SS.

If you are only buying the high steer arms, get them straight from TG. They are now doing USPS Priority Flate Rate International Shipping boxes for $US 40-50. Can also get your ends and pitman arm as well.
Not sure about shocks though, maybe try a freight forwarding company?

No intake resonator on mine. Can't tell much intake noise, between the gearbox whine, wind and exhaust..

I would say it feels like more of a power spot, than a flat spot. Car goes great guns though. Will check the fuel reg though.

dillza_69 wrote:it would be worth trying what i said, faulty fuel regs are common on this motor

Will do mate, cheers.

You can't get the rotor off the stub? Should just come away, nothing but the bearing is holding it on.

Interesting... I am using a 4WD ECU, intake as above and a stock fuel regulator. I am also finding a flat spot around a similar rev range, hard to tell without a tacho. The flat spot is not noticeable, until you rev past it and the power hits.

Anyone having similar problems with a stock 3RZ or is ...

Yeah, lose the body lift. Why is it there in first place?

AFAIK, 3RZ's didn't come with cat converters.

Now I wanna go see if mine throws flames...

hi there well this is what im thinking
32 inch maxxis on my sunnies that are only 7 wide
and then im going to work out how to get the front to flex as it is total crap atm, thinking of taking out 1 ton leaf. might get new shocks

as forr the front diff well as im on a very tight budget im going to ...

What are you having trouble with?

Any financial constraints?

3RZ with a G52 is going to be a whole lot cheaper than the 1UZ.

hi im new to the 4x4 seen and i am on a tight budget. im wondering whats the biggest tyres on a set of 15s on my hilux i could go, my lux looks like it may have a 2 inch lift in the springs. its a dual cab
what other mods could i look at doing on it, cheap
like extended shackles second hand or ...

Good to hear you got some of it sorted mate. Some good info here.

What's your fuel pressure at now with the backfire? Timing spot on? And plug leads ok?

I measured the airbox side of the throttle body to be about 64mm internal.

Fuel cut solenoid?

FWIW, this is my setup:

2.5" tube from TB with a flex going into a VN airbox. No issues.

Do you think the 2.5" tube is a restriction? I have just got all the parts i need to replicate your setup, just need to decide on tube size, 2.5" or 3". What do you rekon?

The ID of 2.5" tube is same as ...

One I prepared earlier:

http://i218.photobucket.com/albums/cc302/yamaha__308/SAM_0610Medium.jpg

Wiper water reservoir fits in between the radiator and airbox. Airbox is held down with bolts through the guard.

The black box (intake resonator) on stock engines is to damp out any extra intake ...

FWIW, this is my setup:



2.5" tube from TB with a flex going into a VN airbox. No issues.

Knock sensor is underneath the intake, next to No 3 cylinder. 1 only. Check for continuity between body and plug.

3RZ. Search.