Outer Limits 4x4 Board

Hey guys thanks for all the advice its quite difficult getting any decent feedback on turbos for td42 in NZ everybody has their opinion however very few it seems have ever tried what they recommend as i have found out with previous turbos that have tried on their recommendation. I still stuck in the ...

Right went through mates shed yesterday and found a couple evo 7 turbos, evo 9 and some vf22. With regard to the evo turbos northside what in your opinion would be the better one to go for? Lucky to have a mate with so many optiosn sitting in his workshop.Looking for something quick to respond got ...

hey guys just playing round with anouther motor:) Fresh TD42 Mate has offered me the above turbo off his Silia to try running 12mm plunger round 120c/c fuel at the moment. Questions is this turbo worth trying? and secondly could i push one of these to around 150rwkw or better i have been told the ...

By Holden V8 do you mean LS1 or 2 series of motor? If so i used the standard ls1 auto bellhousing which unbolts from the transmission and then made a 20mm aluminuim plate to mate the nissan trans. Once this was done was just a matter of drillign some new holes int he standard holden flex plat to fit ...

Will have a look at the CT26 and let you know hopefully over the next couple of weeks will wind some more fuel and boast in to the motor just finished 4x4 event in the weekend and had to tow the mates winch truck must admit egts are 100 to 150 degrees cooler with new turbo and intercooler so its ...

ok finally got truck running for quick drive: fueling untouched at the moment but have noticed so far the following: throttle response is mint, hard to explain but feels like driving my old ls1 powered truck when it was up in the revs Boast builds from 1000rpm and once reaches 2000rpm ramps insanely ...

nice to know about the CT26 :) just to late i guess however it never got full boast until 2200rpm. Mate of mine has GU ute with HX35 fitted by 1500rpm he has over 8pound which is better than my current setup. Will fire up this weekend and see if it makes any boast then was going to set actuator at ...

interesting story to that one when it got fab we were told it was a true water to air core however mate who supplied the turbo has had a good look and reckons its not a ture water to air potentially will cost about 10% cooling efficency however he still reckons should be 20% better than the front ...

Direct link http://i1143.photobucket.com/albums/n626/terranonut/holset%20turbo/holset1.jpg" onclick="window.open(this.href);return false; http://i1143.photobucket.com/albums/n626/terranonut/holset%20turbo/holset2.jpg http://i1143.photobucket.com/albums/n626/terranonut/holset%20turbo/DSC02124.jpg ...

pics of turbo and water to air setup below hopefully this works

Got hx35w with 12cm2 twin school exhaust housing fitted on to manifold hopefully fire up in next week just sorting water to air intercooler for it at the moment. Will post spool up response once going, uzdnabuzd did you get that turbo of yours up and running? Also how much do guys typically advance ...

Going to try the HX35X with the 12cm2 split exhaust housing comes standard on the dodge 6bts. Bit worried about spool up time but the guy has agreed to let me borrow and see how it works before buying.

Cheers

Turbo setup sounds to have alsome potential at the moment still trying to borrow holset HX35 to try interested to see when one of these would make boast. Once have tried that if to laggy was really looking at the 2876 or there abouts will be vey interested to know how your turbo setup performs. Will ...

POW84 am i right in thinking at 1900 your just spooling up? roughly when does the turbo hit 22psi?

Thanks

Rhysta as stated previously have 12mm plunger etc all done on pump already just running in the motor at the moment on low boast then want to get stuck in to the fuel screw and push it pretty hard. Still deciding best turbo to run with just after peoples opinions on the better setup to run for 4x4 ...

All good on the hijack i have a large water to air intercooler setup that i'm running core has been intergrated in to the intake manifold along the lines of Healths setup seems to work extremely well just need to purchase the right turbo to up the boast. Still looking seriously at the 2876 however ...

Swamped i know Aaron personally (he did my pump) and have talked to him in detail about this he runs a geninue garrett turbo on his tuck the cheaper ones don't have correct trust washer and fail at higher boast (happened on my silvia running 18pound) i do beliebe you can retro-fit the garrett parts ...

Ok guys let me know what you think of the following turbo specs my pump will flow 115cc 1000 shots its a gt2871 using .64 rear housing: Also would appricate inout on whether to bother with the ball bearing core or go for a non ball bearing turbo. Compressor Wheel Minor Diameter: 52.70mm Compressor ...

damn figured it would end up with something like that what do you think would be the minimum size turbo i could get away with and still push 150 to 170rwkw? I have been told that the current CT26 is no good for any more than 18psi or something like that. From reading all the posts garrett GT2876r or ...

The current truck with the ct26 and modified compressor side has excellent power up top once you hit 2200rpm it really kicks in and hauls no need to rev beyond 3000 although it easy will, was really trying to find something which will get me out of the hole quicker. The current turbo is a shocker ...

I had LS1 with Cam etc and adapted up the nissan patrol auto worked out really easy, used the LS1 auto bell housing and then made an adapter plate (15mm ally) to mate the nissan upto the LS1 bell housing drilled some new holes in the chev flex plate for the nissan torque converter. We lowered the ...

Ok sounds good when do these turbos come on with full boast? I was hoping to get something that was near full by 2k and then the fuel will keep it going through the rev range.

Also do you reckon i could push one of these close to 170rwkw?

Many Thanks Glen

Hey guys have done a quick search and there seeems to be alot of debate over turbos on the forum however no real 100% recommendations, i have a fresh motor 12mm plunger on the pump and currently running the motor in with CT26 turbo which has bigger compressor wheel (running 12 pound). Once done ...