Outer Limits 4x4 Board

Not to worry...

Ended up getting a new set from klippan

Hi there

I need to replace 2 front seat belts in 47 series ute

wondering what other models of cruiser suit this as well??

60, 75, 78, 79?? anything??

And.... will they clip in to my buckle??

thanks

Everytime i reach 90km/h the noise starts, like a loud racing/rushing sound.

Wouldnt have a clue what it is??

Yeah the pinion nut hadn't been broken into the thread to lock it so easily came loose. Centre is probably on its way to being totally farked, there is alot more (like 30mm) backlash in the pinion now, but doesnt move sideways though. just a pain with the oil leaking and coating the underneath of ...

Hey there everyone, I have replaced the rear diff centre in my 84 HJ47, with what i was told was a centre from a newer cruiser, possibly a 75 or a 79?? It is a 4.11 ratio, the same as standard for the 47. I had someone install it for me, and when i got the car home i noticed oil patches on the ...

finally getting around to fix this. i have a spare diff housing i was told was straight, 2 new rear hubs and new studs. also getting the bearings set right. should i get the diff checked so i know im putting in a straight diff?? OR should i just put new hubs on and get bearings set and new studs and ...

service on injectors including new nozzles roughly $450
then spend the other half on a going over on the car

yes very nice setup, until i can fab like you i am sleeping on the ground in a swag

As you can clearly see we all have had dramas with the idicator light set up.. I used heat shrink over the wires on mine and then clipped them to the guard edge it is a slightly longer set of wires but utilizing the edge of the guard keeps the 40 look but provides wire protection.. that works for ...

Use double insulated electrical wire from the factory lights through to the connection inside the engine bay. It is a lot tougher than the factory wiring. I don't like the look of 75 series lights on a 40, i reckon it spoils that classic 40 look. i have found that you can only use a thin wire as ...

only advice i can offer is dont bridge the glow plugs to the battery.

The only way 10.5 or 12 volts plugs should be installed into a HJ 47 is because someone has bypassed the entire superglow system and replaced it with a home made wilson switch setup. Do you have a manual push button to activate the glows? The normal superglow is pretty much automatic, you glow by ...

bj on roids wrote:75 series lights

do these have the same 3 wire setup

Well, we don't know what model Landcruiser it is, so we need that info. If it's the superglow that's used in 'Cruisers from '83 to '88, they use 6 volt plugs, by applying 12 volts direct to the glow plugs, you'll kill them. As for how the superglow works, there's the glow timer, which is inside the ...

hj 45 wrote:Your plugs are definitely fried too.

thanks

Well, we don't know what model Landcruiser it is, so we need that info. If it's the superglow that's used in 'Cruisers from '83 to '88, they use 6 volt plugs, by applying 12 volts direct to the glow plugs, you'll kill them. As for how the superglow works, there's the glow timer, which is inside the ...

try the owners manual??

it seems the solenoid for the glow plugs on my landcruiser has failed me. so the last few days i have been bridging the positive from the battery onto 1 of the glow plugs to get me to work in the morning, this has worked fine. however this morning it didnt work. have a fawked something up? or is ...

hi everyone ok well anyone that knows a forty reasonably well would know that the wires running to the indicator go out through the side of the firewall and up the inside of the bolt that holds the indicator down. this leaves the wires open underneath the guards. now my problem that i am always ...

i was considering upgrading to the 100 series axle studs, but didnt want to waste time/money if i had a bent housing etc and start breaking 100 series studs. another thing to consider is that im not using genuine toyota studs as i cant afford them. but i think i will go down to the diff shop and ...

i was considering upgrading to the 100 series axle studs, but didnt want to waste time/money if i had a bent housing etc and start breaking 100 series studs. another thing to consider is that im not using genuine toyota studs as i cant afford them. but i think i will go down to the diff shop and see ...

hi everyone on my hj47 i have problems with axle studs breaking from time to time ( to often in my opinion) the axles are turning 33x12.5 muddies but im not convinced this is the problem do i have a bent axle or does my hub need replacing? i have heard from someone to place a spirit level on each ...

trying to do some research on turboing my 2h, have tried searching etc etc. im sitting on the fence atm whether to boost or not to boost. i would like a turbo that will spool early, as most of you know with a 2h you only really get to about 3500 rpm. i'd like a turbo that started at around 1000rpm ...

i did alot of driving around this country in a landcruiser with 33x12.5 baja claws and im sure i was close to going insane from the noise they made on the highway.

id say he knows people that know some people that know some..........

is there a difference in fuel efficiency with the 60 and 76. as said earlier they are the same except for you can tweak the 76 more.
so what is the difference like in fuel efficiency between running low boost like 5 psi and running a higher boost like 15 psi??

i am doing the gearbox/transfer on my cruiser at the moment, is it best i go and pick up one of these hoses from dons, are they a good thing to put on

looks photo chopped i think

have any of you older guys ever had one of these in your car when you were younger? my dad said when he had it in his eh holden it used to blast

yes equaliser has sliders will have to try that