Outer Limits 4x4 Board

G'day. Got a m8 who just put some 2" efs lift springs in the back of his new navara and the front of the spring sit's on the dampner block/strengthen block that is welded to the front spring bracket on the chassis. Just wondering if anyone has came across it.

Have spoken to a shop and suggested to ...

i was looking at using a kkr480 on my conversion. A few guys have said they have run them on their td42 with no probs after 2 yrs, turbo wise. not sure of boost being run in those setups but i know it was above 14 all day, everyday. Their a copy of garrett. Got a couple of m8's running the kkr430 on ...

I'm sure someone will correct me if i'm wrong, but in regards to the "cheap" KKR (and most likely alot of the cheaper chinese units), PEER drift team actually had/got sponsorship from KKR i think it was, and used their turbo's for a whole season without any dramas. They copped the usual rediculous ...

Just wondering if one of these turbos below would be acceptable on TD42. can get my hands onto them cheap and not to indepth with turbos. More coments the better. Cheers.

kkr430 -
Compressor side
Inlet pipe 70mm, outlet pipe 50mm 48 trim compressor; inducer 53mm, exducer 76.5mm
Exhaust side
0 ...

anyone fitted there manifolds yet? Any custom setup's get done?

G'day. Just noticed on my GQ the other day, that when i have my hubs locked in, im in 4wd or take off quickly turning or up a hill. and when i turn its like the rear tyres are skipping and i get a shudder/bounce effect through the car. Does not happen when going straight ahead. Its got a lsd in the ...

G'day. Going to be putting my ute up for sale in the next month or two. Just wondering whats the go with suspension mod's and RW Certs in QLD? Anyone had similar situation or know of rules?

Got 3" spring lift and 2" body. Would take body lift out if that makes to pass RW.

And don't worry im ...

SSS pulsar fit ftraight on i have heard. Do a quick search. Im sure its been discussed before on here.

lol, guess he wasn't very good at skipp'n then. Always getting his legs caught up.

Check wearing on the edges of the belts. Try turning the belts round. Might be a pulley just otu of aligment. They tend to make a noise on some engines and some belts.

First check your pints gap. Second did you remove the dizzy? If so you will ahve to get no.1 cyl at top dead center. Then fit the dizzy. Make sure that you rotor button is inline with no.1 cylinder on your cap. Then just adjust timming to suite.

Sweet as bru21. Short, to the point and what i want to hear. lol. Yeah i knew bout the body lift one and was unsure bout the engineering one. Guess i'll be leaving the springs and get my body lift done. Thanx boy's. Hope to see ya's out there soon.

G'day. Got a GQ ute with 3" spring lift and 2" body. Now im in brissy and was wondering if anyone has had their's done and how much it cost them? I need to get my bank balance in $$$$$$$. :rofl: Im going to try and ring some engineers round the place but i don't know if they all do 4wd engineering ...

You shoudl ask BigGQ. He run's a 4" body lift in his GQ ute.

its a self tensioner setup. it will be 15mm spanner. Put on the top idler puller and move it anti-clockwise. Will bring the arm down and remove the belt. Easy as that.

I just made the facia out of a bit of plastic sheeting i had laying around. Looks great ay. Very clean look.

I have mine mounted in where my ash tray was, as i don't smoke. I made brackets inside and then put a faceir around the cb. Looks great.

I reused my shims when i did mine. Came up perfect when i put it all back together. Within specs straight up.

No way i'd ever move their. Love aussie land more than my 4bying. Could never do it.

Ok got this off the QLD site.

- The ride height between the rubber bumpstop and the corresponding metal stop may be reduced or increased by no more than one third.

- The rebound travel measured between the rubber rebound stop and the corresponding metal stop (or extension of the shock absorber ...

lol. Who cares. On with the thread............

So has anyone had a 3" lift engineered in qld? I beleived its 1/3 of the bump stop in qld? Anyone know the bumpstop soze of GQ? or could you get a new bumpstop engineered and it would pass? I h8 transport departments. Why can't they let us have our fun. Half the time they don't even know what they ...

G'day.

Im after some tyres for me 4by. Can get me hands on some maxxis mudders for a good price. Anyone heard of em and how they go?

Cheers

Im finnishing off my gq coil cab lift this weekend. Its also a 3" lift. I got castor bushes off 4wdstuff so i'll see how they go.

yes will you have to move thee arms from the 4by. You will have to press the bushes out. i have just done mine as im putting in 3" lift.

G'day.

Installed my body lift (GQ coil cab) and noticed when i went to put the middle locating bit in the bracket that it dosn't give the line much play.

Wondering if anyone knows of any places or shops that sell extended clutch lines for 2" body lift Around the redlands area in brissy.

Gonig ...

Anyone had fights and won over transport of how high you can really lift a vehicle with them having a go at ya for the lift?

Talk to ludacris on er. Hes got his own shop at caboulture. Hes great


Cris's 4 X 4 Accessories & Suspension 0417 616 764 www.4x4accessories.com.au

How much would you pay for Goodyear MTR's v's Baja Claws? Aprox. (33x12.5x15)

If its just a low pressure line, i would replace the hose clamps and also the hose if it looks to be getting old or worn. If its leaking on high pressure lines check to see if everythings tight. If everythings tight and its still leaking, it could be the o-rings on the lines connections if they seal ...