Outer Limits 4x4 Board

Thank you hulsty
but what longer springs ? OME - Dobinson ?
what is the best ?

Giacomo

Thank you all,

I know that it is a italian dealer , but it does not have experiences on these articles,
therefore I wanted some feedback from that it has already installed these shackles also on other models of series 70 .

Giacomo

Hi all,
I would want to acquire extended rear greasable shackles for my HZJ71 LHD 2008 .for flex and lift .
Snake Racing or Precision Engineering ?
what is the best ?
thank you

Giacomo

Toecutta wrote:

giacomo.m wrote:Hi,
thank you all, the rear LSD it is genuine,not aftermarket.

for Toecutta : which fluid uses in LSD ?

Giacomo

Gia, I think its a standard 85w LSD oil but I would have to check

thank you Toecutta
but it is standard 80W/90 or 85W LSD ?

giacomo

Hi,
thank you all, the rear LSD it is genuine,not aftermarket.

for Toecutta : which fluid uses in LSD ?

Giacomo

nobody can help me?
moreover I would want to know which fluid to use in this LSD rear diff
thank you.

Giacomo

Hi all,
I am owner of Vitara 1.6 16V 1992 automatic transmission and LSD rear diff.
now I have grinding noise /wind up and binding from rear diff.
clutches to replace ?
I can remove the clutches or I must acquire a new rear diff ?
thank you.

Giacomo

thank you
I have 4.875 ratio,
and I can to fit my ring/pinion -differential and front drive shaft to cast steel housing and third member ?

Giacomo

Hi all,

I am owner of GV 3 door LHD 2001 with J20A engine, manual transmission and I have front carrier aluminium broken.
I want to replace it by a more solid carrier.
therefore which model of Vitara / GV have steel solid axle ( housing and third member ) ?
which gear ratio ?

thank you ...

Thank you barneymutt

Giacomo

Hi all,
I'd like to replace the 6G72 12V SOHC 3.0L in my '92 Pajero with a 6G74 24V SOHC 3.5L. Is it a drop-in replacement physically? IOW, are the motor mounts in the same location and will the output mate-up/bolt-up to the V5MT1 gearbox ?
Thanks for any help.

Giacomo

xagtho wrote:giacomo, check your 'crank angle sensor' and its connections, and 'cam angle sensor' connections if it has got one

thank you xagtho
crank angle sensor and cam angle sensor in distributor ?

Giacomo

Have pulled the bash plates off underneath my 3.0L paj to do some major service and have driven through creek crossings without the bash plates (yet to put them back on) and have had no problems with stalling. I would suggest you have an electrical fault somewhere that is caused by water over a ...

Sorry Giacomo, I can't think of anything low enough to get wet in 200mm of water and stop the engine. :?

The way it will restart reasonably soon suggests it's water splashing on something electrical, which dries quickly.

Have you got all your splash trays/guards on place? I can only think the ...

Sorry Giacomo, I can't think of anything low enough to get wet in 200mm of water and stop the engine. :?

The way it will restart reasonably soon suggests it's water splashing on something electrical, which dries quickly.

Have you got all your splash trays/guards on place? I can only think the ...

thank you all,
for Wacko : it is exactly what it succeeds me. but exists the possibility to read to the codes error? where the connector for the diagnosis is placed ?

Giacomo

Hi all,
I have Pajero 3.0 V6 1992 LHD Super Select and I have the following problem: when I take of the holes with water(200/300 mm ) the engine is dead .
no light "check engine" and after several tried you of ignition she is recrank .
what is the problem ?
thank you

Giacomo

Hi all,
have you some pics of hoses brehaters of gearbox and transfer box for Pajo 3.0 V6 1993 LHD Super Select ?
thank you

Giacomo

Hi all,
I am owner of Pajero 3.0 V6 1993 LHD Super select.and I have problems
to right hand inner shaft removal.
I have tried also with an sliding hammer to flange from differential carrier but without result.
you have some tricks ?
thank you

Giacomo

Hi all,
someone a site that would give a manufacture data for a given frame number (VIN decoder ) for my Land Cruiser ?
thank you.

Giacomo

thank you for your reply.
also I task that the E2444 is that right one. I have already acquired the E2443 but it does not go well, because it has two open sides. while the E2444 has the side low closed on the box airfilter, as it genuine part.

Giacomo

G'day all,
strange.41 readers and no answer.
do not exist? or problems of efficiency on this engine ?
thank you.

Giacomo

Hi all.
someone know exact K&N airfilter part number for 1HZ in HZJ105 ?
it would have to replace the genuine Toyota :17801-67060
thank you.

Giacomo

Honestly sometimes its like getting blood from a stone there(MTQ), you won't find anything on their web site, they are National, find your nearest and go in and order what you need, they don't carry much on the shelf it all comes from Sydney. It does save a few bucks though. They aren't really ...

thank you KiwiBacon

but the tap and dies find theselves in Europe ?

MTQ Dandenong has the cheapest braided lines, order a set for a TD42 kit, you will need an adapter for the oil line, the fitting must be a JIC type into the turbo oil supply as the fitting locks the bearing cage, or else turbo failure.
I would suggest 3/8 to 1/2 inch water hose will be enough as ...

Thank you all,

in the table of Turbo Master are : " C.H.R.A. " and " A/R " what is ?

Giacomo

wtf you do realize that the bloke could be italian? and most likely non english spoken? ;)

Giacomo, if you get rid of the rear section you probably will smell diesel fumes... and the car will also become louder, cause you are getting rid of (pretty sure) at least 1 muffler.

G'day udm

and ...

Hi all,

I have a HZJ105 (1HZ engine ) with aftermarket AXT kit turbo,
the nameplate to turbochargers is : 1B (TB ?)012 4J
14411-17D03
471024-0003
which turbo is ?
Garrett ? Toyota ?
moreover me it seems that it is not water cooled,like would have to be the kit of AXT.

Thank you.

Giacomo

Hi all,

someone has removed rear exhaust to HZJ105 ?
troubles ? any fumes or smell inside ?
the sound level is increased ?

Thank you.

Giacomo