Outer Limits 4x4 Board

Part number is 40040-01j00 $31.40ea rrp. Nissan have 140 in stock

08/87 is the month and year for the first build.

I have two of these engines left so if I can be of help send me a PM.

Trev

http://www.outerlimits4x4.com/phpBB2/ft ... ight=group

The ring problem was modified back in 01 however bogged is correct they have alot more issues that just the ring design.

Yes the new engines have a different ring and piston design. The date was a running change around the end of 01.

Thanks Bogged, I will give them all a go and see what happens.

Thanks mikmav, I think you are correct that it is not the sort of thing to put on the self for a rainy day, I had planded to try the other forums but having been a member here for a few years I thought i would see what sort of response I received. If I end up with a few people that do want one not ...

I think you find that $6500.00 is plus GST $7150.00 (which is a good deal) unless it it for a td42 which we do for $5700.00 inc gst. The price we have quoted i can assure you this is the cheapest you will find. Trev

We are a metro Melbourne Nissan Dealer. I have been bartering with Nissan Motor Co on a group deal of Nissan Patrol ZD30 engines for the outers forum given there reputation for snapping the tops off pistons. I need x10 sales to make this deal happen. The RRP on these units is $9929.00 the price we ...

I have x2 in stock at the old price $95.00ea + freight or pick up from Brighton Melbourne. Freight to most major towns around $20.00. pm or call if you still need one 0423-779593.Trev These are Genuine ones.

These engines have a problem with leaking oil from between the block and the timing sandwich plate due to a lack of sealant when assembled. The oil blows back and can make it look like the sump gasket is leaking so wash it down and keep checking on it.

It is the front hub drive flange (what you have pictured) bolts on in place of either auto or man hub and takes a grease cap over the top.

king pin caps 40022-01j00 $105 ea

drive flange is used only gq/gu
mq and g60 are different

Drive flange 40261-01j00

fx324 would be great they are easy to use and for someone starting out would be the way to go.

Only the .5 one is $16.00 odd bucks but the others are between $3 & $6 ea.

I have been running TJM's for about 12 months in gq front & rear and except for some early set up problems they have been great and they get a hard time. The set up problems were the front solenoid died because the piston had been machined incorrectly the groove for the oring was too far forward ...

You can buy these shims from Nissan part numbers and sizes as follows
40571-01j00 0.5
40603-44000 0.762 mm
40604-44000 0.254 mm
40605-44000 0.127 mm
40206-44000 0.075 mm
Nissan's Brisbane warehouse is showing stock of all
Hope this helps

The lower bush which is the one with the large hole (diff end) is 55135-01j01 same as GQ. The upper bush I have never had to replace on a GU but having a quick look at it it is differant. The upper GU bush has a dust boot over it. If your mate has the rod out of the car get him to check the ...

GQ's only have a single piston rear caliper. If you try a Nissan Dealer quote part number d406ms20x5 they sould know anyway,trade they are $76.60 or PM me for a deal.Trev Brighton Nissan 95639902. These are a good pad.

THE PART NUMBER YOU NEED IS 2120003J00 76.5DEC.

Only 4.2efi GQ's have the larger twin spot calipers on the front the rear caliper size is all the same. 15" rims do fit (brand pending)over the larger calipers but there is a very small gap between the rim and caliper.

THE CALIPERS ARE ALL THE SAME. THERE ARE TWO PADS LISTED UP TO 10/91 AND 10/91 ONWARDS THE ONLY DIFFERANCE THIS THAT THE LATER PADS HAVE WARE INDERCATORS ON THEM.

Yes the mounting points for the hinges are differant one mounts flat one mounts upright.

Yes there are 6 types 1.1mm to 2.1mm. you should measure the end play on the shaft and order to suit. But if you are like me just go for somewhere in the middle 1.5mm 39253-01j02.

If it is still there once you have had it balanced replace the panhard rod bushes,upper (small hole) 5513501j10 and lower (large hole) 5513501j01 they should only be about $30.00.

TB42E (EFI) from factory are all electronic ignition.

What height body lift have you fitted? If you have not gone any higher than 50mm you should be able to just heat and bend the sticks without cutting the floor. Start by buying a new gear stick boot 74963-06j00 should be about $35. The transfer will need to be bent forward and the gear stick ...

Can you tell which side of the engine it is coming from? Leaking exhust manifold has been know to cause a ticking sound.

You should also extend the rear brake bias valve spring bracket.