Outer Limits 4x4 Board

Guys, a mate of mine is setting up a warn hydraulic winch with a Toyota MR2 power steer pump. The pump is divorced, electric(12v) ,so will set up a tank and readily avaliable solenoids to operate the critter

Guys, i have three winch bars i want to get rid of.All ARB ,2 low mount, 1 hi mount. 03 9740 6300 if your interested. Cheers Dave

The people to speak to would be Marks Adaptors or have a look on their web. Ther is a full list and specs there. Dave

choosing a fridge is a pain in the A#$%E. I finally chose to run a Trailblaza on the back of my ute, and dont regret it for a moment. Have also slipped oneinto the back of my GQ. Rain, hail,mud or shine they have not missed a beat(no i dont work for them).For a bit of public knowledge, the Aust ...

Does any one know a rough price for the addition

I found out today that some of the TD42's use 2 Z9 filters. Fram filters have both full flow and bypass filters. I shall be using the full flow filter and they cost me about $5 each. Will screw the first one on gently and go from there. Let you all know

Just purchased a nissan with a TD42 andwas wandering: this engine has two Z9 oil filters fitted; are they the correct ones? Do they cross reference with the nissan filter? . I will go buy two Z9's to see for myself, but if any one knows any thing ,it would be appreciated

Ever thought to replace your rods with cromolly? My 45 has been lifted 5" undersprung and i am running double arm and cro-mo rods. They take some punishment

Thanks guy's for all the help. Will give the big cheeez and rolling bearings a call. Many thanks again.
Dave

Known2, did you get the pics i sent to your phone on Sunday. Your mate answered when i called and said he would pass message to you.
Dave

4sum4, i am trying to find a supplier of rated, cro-mo, teflon lined rod ends.as opposed to "tie rod ends", in which i only supply and fit genuine to customer vehicles.
Dave

Got a set. Done 65,000 and still going. Quiet on the road ,very good traction in the wet, and still as good as BFG mud. Definetely getting another set. Tyre size is 35x12.5R15

Does any one know were to get cheap ones in Melbourne

If you have only two solenoids then you canpick them up from TJM as they are all TMAX variants. From memory they are not exy, but will let all know in the morning as i dont have my price book with me.

It comes down to the old race saying. More air+ more fuel = bigger bang. Bigger bang= MORE power. Why do you think 4-6-8 cyl. vehicles run cold air intake? . Why do turbo's run coolers? Colder ,denser air. 2 snorkles is the cheaper alternative.

TJM or ARB did not make a cradle for the factory alloy bar. Toyota fits the winch without one(not a good option). Take your measurments of the winch and see how much room you DONT have. Have done a few now and they are tight. If its too much hassle for you look for a second hand steel or ECB alloy ...

I am in for a couple

Yes chev do have a factory air box and so do holden that can be easily modded to accept a snorkel. Chase through the importers for a 14x4'' air box, from either chev petrol or 350 Oldsmobile Diesel(chev). I run one of these with twin snorkels on a 45's cruiser. I can take pics. and send them via ...

pc, have you ever had m+s doe a drive shaft for you??? Had one done there, charged like a wounded pig, and had Melb. rebuild it properly. DONT GO THERE
DAVE

F@$%#>. Did you pay that much????. Gave mine to Dave at Melb. Tail. and it cost me 300.
Dave

Are you looking at cooling or keeping it clean? If its for cooling go PWR Alloy..This is what i have done and cooled(froze) the 400 SBC idleing for 3 hours on a 40 degree day to test it . Welcome to check it out. Mine happens to be from a 75, bit taller, and well worth the grand to do the job ...

Yeah Allianze insurance, 4wd Dept., are seriously worth ringing. Must say, you will get a better price if you are a club member. I pay $600.00 full comp. rating one,(thanks to my wife) for FJ45, hot chev, rear coils, 6" front lift, F&R lockers, Bobbed Chasis,F&R winches and 35's.Am covered all round ...

If you can stretch the budget, pick up a SPEEDWERX bender. Not a cheap unit ($850.00/Bender.$800.00/Die) but does an awesome job and sooo simple to use
Cheers Dave

Yes, G60 on GQ. Study the picks
Dave

No such thing as good and cheap. What sort of budget you got.
Dave

[quote="not not"]yeah chris get ya act together and service theses people. They are practically throwing money at ya !!!! :finger: :finger: :finger: :finger: Hows those four grab ya? Side walls mate I run mickeys so i dont have probs like that. [size=7][/size]And yes it has taken me a whole day to ...

Give Opposite Lock a call. 99.99 % sure they do a step or get them custom made. There is a few of us who do custrom sill sliders/steps.
Dave @ Play Time 4x4

Chris, does the outer edge of the lock ring have a bevel or radius or is it square off the laser? Hanging out for the pricing as quite a few of my customers are really keen to get them.
Dave @ Play Time 4x4

Yeah, hard call. i would go the locker first for high country trips, BUT please dont consider a T MAX . Like others have said, look for a second hand WARN or buy a brand new Warn TABOR. Brand new , USA quality for $1150 . Cant go wrong, but thats my opinion
Dave

Get onto street commodore forum. There is all the diagrams you could want, if your still stumped ring Scott @ Chipcontrol 03 9740 3363. This is his specialty, Tell him Dave @ Play Time 4x4 sent you. He is a wealth of info.
Dave