Outer Limits 4x4 Board

lets see some pics please, and what was the $$ outlay??

Rob

new mitsu's and toyota's built in Thailand...
probably in same factory complex...

Rob

Sometimes if there is a kink in the chain it can be a pain to wind up n down...

or the chain has been deformed..

Rob

Where did you find the pic ??
that looks awsome...
i want...

That triton/ L200 looks awesome....ahhhhhhhhhhhh

How bout some pics of the trailmaster lift please ???


Rob....

any suspension components ???

Springs/ shocks....

Rob

Hey Basti,
welcome to the board..

Thats one nice looking truck..
Do u have any extra info plus photo's on the suspension lift ??


regards

Rob

There are few kits that come out of Asia.

The ultimate suspension ones (Like above and have been sold here for a few years by ORI)
Then there's the Sun Products one.. Lots a yellow bits on it and our friend from the US with the challenger has one fitted..

There is some major differences with the 2 ...

Its ok scott, u can still come and play with us..........

Awesome idea with the plugs replacing the ton/tie down points..

Shall endevour to get some up to date pics of my truck..

Rob
Sydney

Some triton's from around the world...

Here's some pics of mine, old and older...

im pretty sure that is a SUN kit from thailand...

Rob

As with most servicing for the 90k > 100k u will b up for many things.
At that mark the triton is up for several things :

# timing belt (possible will need other items here as well, like - water pump,cam seals, Crank seal, belts, pulley bearings etc)

# spark plugs (platnium type)(to get to these u ...

interested in the ball joint spacers

Rob

Thanks frank, o wise one...

Rob

Hey scott,
thanks for the info...

The rear of the triton should be ok and im sure the front will be fine.. yeh u may have some drive shaft issues (nothing a spacer can't fix)..

will try to get hold of some engine mounts and see if they can be ADJUSTED......

Hey FRANK, r the engine mounts ...

Has anyone ever done a engine lift ???

Would loike to raise the engine/gearbox approx 20mm (have bodylift)..

The gearbox looks easy to do but unsure about motor...

Any ideas ... (for a 99 v6 triton)

thanks

Rob...

I'd be very interested to see how this turns out... i did look at some coil conversions for mine in the past...

from memory the challenger rear end is wider than the triton.. Some of the earlier model pajero rear ends r ok.. maybe look at using the challenger trailing arms...

Ask frank ...

Hey frank,
thanks for all your help...
Ill adventure to the auto shop tomorrow..

what model paj is the Gen 2??? (or anyone else know)..

Thanks for everyones suggestions...

Rob

Well tryed autobahn today as well as another parts place and no listing for the arm for my triton...(that was in the powermax cat)

Im un-sure if the Paj one is exactly the same...They didn't have one in stock so wasn't able to even check it out...

May have to bit the bullet and go genuine ...

As the heading says i need some help to find cheaper parts for my triton..

Called Mitsubishi today about idler arm and top ball joints...

The ball joints (top) aren't to badly priced at around $85 each but theen i got the price for the idler arm...
R u sitting down (luckily i was)....$333 ...

yep, know this well...
32" MTR's don't help me either.. If i go 33's it will be even better...

I deal with air bags in a emergency capacity..
They r tricky and unpredictable things so be real careful playing around with them...
On many vehicles even if u pull the fuse the SRS system can be still active for as long as 30 mins (some even longer)..
They operate in the area of 100th's of a ...

Anyone out there got a set of lifted rear leaf spring for a triton or even paj that they won't t get rid off...

Thanks

Rob

Hey Frank,

looks awesome. Cant wait to see the in-use pics...
nice BLING look with the red paint...

Rob

as usual with mods 'they r only limited by ones wallet, their misses and there minds'....

As Frank said bar, suspension lifts, wheels/tyres, gears and lockers (although i think there is a rear ARB locker for the triton)..

Go on, u know u want to....

Rob

My triton has the following mods,
40mm bodylift
extended shackles
removed front swaybar
front bumpstop mods
Torsion bars twisted
Canopy
32" MTR's on 15x8 alloys
B/bar, T/bar
Arb siderails
2.5" exhaust

future mods...
Longrange tank
Gearing
Locker
33's
more suspension mods (possible ...

nice photography with the tents..
great shot.

some more in the set