Outer Limits 4x4 Board

x4 can also get dragged in through dipstick tube

your local holden dealer will supply fit and certify a restraint but they are intrusive

think ill stick to my 100w hids

make sure you post up some pics along the job mate as i will be doing this to mine soon as well

Thylacine wrote:Should be easy enough to figure out.
What are the terminals on it labelled?


ed

found one there was 2 wires i wasnt sure of 1 is winch overide the other is a second power wire used if you dont run the n cab module

i have an old rotronics rfc12 here that i need a wiring diagram for does any body know where i can get the info (their website is pretty useless and emails have been sent to their tech center)
if any1 can help it would be great

has any one had this drama with their deo min is a 2.8 td 94 mod

im hoping itt is just detents but expecting something more sinister

valve seals not that hard you can buy a tool to do them in situ

turbo rebuild ring
Precision Turbochargers

Unit 51/93-97 Newton Rd, Wetherill Park, NSW 2164

p: (02) 97565757
usually 300 to 600 depending on whats needed

what sort of price??

15 psi would be good enough for what i want i have been spoilt with my old disco 300tdi 20psi boost
it went quite hard
not going to that extent with the deo though

What are the max boost pressure that the turbo and engine can handle it is 10 psi stock un intercooled id keep the boost at 15 or under but dont want to strain the turbo to much

so far ive done a 2.5 inch zorst with 3 inch dump pipe
and done the pump tweak i will do boost next week

so far ive only done pre-boost fueling and fuel rate
this is done by winding down the star wheel and rotating the diaphragm
on the injector pump
whent from being pitiful to pretty good but ...

got one made with a full 2.5 inch system for 600 bucks every where else wanted 400 for the dump pipe alone

tranny flex plate and spacers torque converter shifter oil lines and cooler
engine crane makes the job easier
not a super hard job but time consuming should be able to do it for under 1k price of gearbox is the exxy bit

where can i buy a dump pipe for a 4jb1t tf rodeo online would be great

i know that it is in average condition but was hoping for more than 3 so im keeping the winch at selling the rest so there is a low 200k 300td1 and r380 up for grabs as well as a gq conversion etc
all the radio gear can go in the rodeo i might get some pics up of the bits and pieces i also have a ...

im actually thinking of parting it out as the bolt on bits are worth more than 3 grand

so if ya need disco bits watch flea bay

i was thinking more around the 5k mark but also im looking for a 4x4 dual cab but money talks

i am thinking of selling my disco

it is running gq diffs 80 series springs part time converted warn winch and other odds and ends 35s flares full length roof rack and cargo barrier spotties dual batteries uhf dvd tough dog big bores with in cab kit etc
it is a 94 model 300tdi with hi flow turbo ...

i used cam tech in Sydney last time i got one made and a new custom grind 6 cyl cam was $250

as for turbos you can get yours hi flowed also mine only cost 600 to get done with a full rebuild it made a lot of difference

belt it will be a 300tdi so will more than likely need the full kit (about $300)

it seems there is hope yet
time to get to work on it again (i might still buy a fender though)
i was going to keep it as a trailer toy buy i might finish the new modsand keep it on the road

well looks like im going to pull the disco off the road come Christmas time as these new laws are looking grim and it is not worth spending the coin id need to to get it to pass under the new scheme
so i am thinking of buying a 2000 onwards fender 130
my question is who has one what do you think ...

all i need to do is find flare piping

i can repair them myself and these are twice as thick as the lra ones and he is using weave matting so they will be strong im still not keen on the idea of plastic flares after seeing a few on trucks around here the glass ones look better IMO

who would be interested in a set of fiber glass flares that are similar to the lra ones but a little wider and stronger for about $400 ish?
ill get mine within the month and post up some pics

its sounding like 400 a set for the custom made ones 75mm wide i should have a set in a fortnight

not 100% on the details as yet dont know if he wants to make many sets as yet

im getting a set made for half the price of lra