Here you go .............http://www.v-8.org.uk/engineno2.htm
I have another list of my own which I could post up .... that gives the BHP and torque of the various RV8 engines for the different markets.......
Ian
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Search found 7 matches
- Thu Sep 06, 2007 12:34 am
- Forum: Rover
- Topic: 3.5/3.5 identification
- Replies: 8
- Views: 651
- Tue Sep 12, 2006 9:45 pm
- Forum: Rover
- Topic: Hall effect distributor
- Replies: 6
- Views: 445
Will the Micotech control EDIS? If so, then junk the dizzy (but leave it in to drive the oil pump) and go for Ford EDIS8 ……… plenty about on eblag. Use a ford transit toothed wheel on the crank pulley and a Ford VR sensor………….. a few over here have done this mod and use Megasquirt or megajolt to driv ...
- Wed Aug 30, 2006 12:41 am
- Forum: Rover
- Topic: transfer case (DefenderT230) bang
- Replies: 16
- Views: 639
If the front prop rotates when in diff lock then the centre diff cross pin must be OK ................ Sounds like a front Halfshaft ...... ususally the short shaft and if its the 10 spline it will have twisted and broken right at the splines ....... the broken part in the diff can be a bar steward ...
- Wed Jul 26, 2006 12:33 am
- Forum: Rover
- Topic: V8 lifters....
- Replies: 11
- Views: 562
Yeah, I’ve used solids on 3.5’s ………….. but only on race engines where the std hydro’s run out of steam at 6K rpm. They should work OK on most cams but depending on the manufacturer of the solids you will probably need to shim the rocker posts to get the correct clearances …….. Solids make the engine ...
- Fri Jan 13, 2006 11:46 pm
- Forum: Rover
- Topic: Setting the timing on Rangie V8
- Replies: 9
- Views: 469
Adam, I don’t post here much but this may help :oops: To check that the TDC marks on the balancer are actually TDC, use a dial gauge through the no 1 plug. Alternatively use an old plug and a manometer (water U guage). Replicate the balancer marks up to 30 degrees BTDC. Disconnect the vacuum adva ...
- Mon Nov 07, 2005 2:57 pm
- Forum: Rover
- Topic: Need starter motor
- Replies: 7
- Views: 431
prestolite aren't great.... I think crap would be a better description :x ............... and they leak water into the bellhousing when deep wading. Rebuild the Lucas ;) .................. its about the only thing that Lucas ever got right. I have just finished rebuilding mine ........ the sooner ...
- Sat Oct 08, 2005 8:46 am
- Forum: Rover
- Topic: LT 230 questions
- Replies: 8
- Views: 453
Look here for the info 
,
http://www.ashcroft-transmissions.co.uk/part_9.html#pa1
Low range is the same on all LT230R/T's
Ian
,http://www.ashcroft-transmissions.co.uk/part_9.html#pa1
Low range is the same on all LT230R/T's
Ian