Outer Limits 4x4 Board

http://i14.photobucket.com/albums/a347/strawbqwerty/P1070687.jpg Shortened series 3 body on a range rover chassis, Isuzu 4bb1 diesel, Isuzu msb 5m gear box, LT235 transfer case, four link rear, three link front with panard arm, dam long springs and shocks, arb bull bar, 12 volt and 24 volt ...

My old ute has some of the gear for a comp vehicle. Mainly the suspension. Is a hybrid. Range rover chassis, with a shortened series three ute body. Has a Isuzu diesel. Suspension is a custom 4 link rear and way long springs. Front has a custom three link with panard arm and not so long springs ...

It`s NA and it only smokes a bit on take of.Due I think mainly to the typical lag of mechanical fuel governors.Plant the foot more fuel than the motor needs until the revs match sort of thing.Good to hear it looks better than when I brought it.Had to fit the flares and legal bumper for a rwc.So ...

Yeah It`s the ute of Ebay later last year.And I`ve seen these posts.The best the seem to give is the kilowatts .But I took the ute finally for a run a couple of Sundays ago.It went like a cut cat,hence my interest in the motor specs.Was 1 gear higher than the Landcruiser 2 h powered beast that I own ...

G`day all.I have a ute with a Isuzu 4BB1 motor in it.Great motor and happy with it.Just don`t know any specs for it.Have trolled google and aulro site with no success.Would like to know what kilo watt's it has,torque and idle revs.
Cheers

My old truck was put together way back about 1982/3.Then all the maker did was take it to the local police who then checked it out and passed it as ok.Was a extra letter or number on the rego.Had no problems when I changed the motor and went to Vic roads and updated the engine number.They looked up ...

The old manual that I have states that there should be a glow in the glow lamp after 15 seconds.If not it`s time for new plugs.There is a variety of volts in glow plugs that fit 2h diesels.Rule of thumb though is higher the voltage the quicker they glow and shorter the life.I think from memory they ...

Did some thing similar with my truck.The gear box is behind the front seats.So there was already a remote gear shift but the 4wd stick was still behind the drivers seat on the floor and a pain to get to.Tried with out much success to have one remote stick.But ended up with two that are slightly ...

Read a review on them awhile ago.To summarise the review.Absolute crap with a capital C,R,A,and P.Hence why the did not sell.Small underpowered diesel.2ltr from Peugeot .Transmission that was a shocker.Poor build quality every were.But that was only one review,so there could be some good news on ...

I have also just brought a tacho for my 2H.The brand is V.D.O,you can get them in either 4000 max revs or 8000 max revs.They are 2'' diameter in size.I paid $140 for mine.Bit of a fiddle to fit though.You get it wired up.Get your self a hand tacho that can take a reading from the centre of the crank ...

If you are talking about the transfer case only there is no mounts.There is also no tail shaft hand brake drum on the transfer case.If you are talking about the gearbox and transfer case together.Then there is issues.Ohh man are there issues.Unless the bell housing of the H gearbox matches the gear ...

You can go coil over spring.Son`s Hilux is set up like this, very flexy.Also is a s.o.a set up
Cheers

Better having a volt meter,Easier to install,Can even get a meter that is part of you battery terminal.In dash one is dead easy too.Know this as I have just installed one.
Cheers

Imlach in Clayton would be one to try.
Cheers

My trucks intake is behind the drivers seat up near the roof.It sucks air from out side.But there is only a sheet metal box that holds the air cleaner inside the cab with vents to the outside.And yes there is just a little bit of noise.From the air filter box the intake pipe drops down under the ...

Diesel motors due to there higher running temperature have greater tappet clearance to start with.So on start up can sound quite rattly till they warm up a bit.To still sound rattly after warming up means time for adjustment.
Cheers

Does the sound lessen when it warms up?If so the tappets may need adjustment.Certainly a noise the 2H is known to have.I unfortunately sit be side a 2H in my truck,so tend to hear the motor noise just a bit.
Cheers

I also have a 2H in my truck that has mechanical stop and fuel over injection for start up.There is a bit of bush mechanics to get it set up though.Need to fit a longer arm to the actuator arm on the pump.Need to fabricate two cable holding brackets.Need to mount cables to pull from both sides.Need ...

A old bbq gas bottle makes a great receiver.Is a pressure vessel to start with and was originally made for far greater pressure than a air receiver.Lot of home made compressors use them.
Cheers

Flanges are the same too.

When I brought my truck it had a spacer of about 20mm fitted to the rear prop shaft.Dam thing kept working the bolts loose. There was only bolts that whent through the diff flange, spacer and prop/uni joint flange.If you could some how bolt directly to the spacer from both flanges it might of been ...

Brought a used set of 235/85/16 Geolanders of Ebay.Were about 70% tread.Not the most agressive mud tyre,but not to bad.For the vehicle they are on they handle real well.Due to them not being over agressive I`m using them as a daily drive tyres.Off road they seem to be quite good also.Read that they ...

It`s got a rear locker now and just a few renovations and upgrades.

This with unimog axles would be a good unit.
Cheers

I went down the same track as hustly 60 rear diff,wich gives you a hand brake in the rear drums, and the ifs hubs on the front.Also used 60 series springs front and back.
Cheers

Have recently had much the same problem.Had replaced the 45 series front springs with 60 series springs.This would have moved the axle forward about 50mm so I redrilled the locating holes in the axles perches and bottom plate to split the difference.This still altered the caster angle abit so fitted ...

Pay to check were the oil returns to the sump and make sure that the path is not blocked.Vehcle I owned had a cronic sluge problem.During work done on it,it was set on fire twice.The return path for the oil was blocked.Oil filled the rocker cover and pumped back through the air cleaner onto the ...

On ebay at the noment there is a place in Dandenong Vic ,Ambassador industrial is the name.Sell both the under edge fixing and side fixing in two widths.I have brought the under edge fixing wider profile at $8.50 per meter.They of course will post any were,or as I did as I live not that far away ...

A 60 series are a 30 spline axle.I have confirmed this recently when I brought a auto locker.
Cheers

There are a couple of contacts in the starter.One on each side of the solenoid.Heavy wires going to them."L" shaped when removed.they can and will wear were the solenoid contact ring touches them,much like points.The one sending power to the starter may be cactus.They are easy enough to remove and ...

Got two questions.Will a H diesel bell housing fit a 2H diesel motor?Have removed the H motor from my truck.Have found a engine mount that is diferent to the others.The H motor has two piece bell housing with the gearbox/transfer suspended of the motor.There are mounts on the bell housing half that ...