Outer Limits 4x4 Board

ohj. no worries. thanks. does the chain need changing in them at 100 thou?

not sure now. i just read a post on another forum. some ppl seem to think that mk triton diesels have a chain.............i thought it was a belt. the manual talks about a belt...

my 04 triton is due for its timing belt. i was just wondering if anyone has done a timing belt on a 2.8lt turbo diesel before. i have done a couple of timing belts over the years but never on a diesel.the local dealer is going to charge to charge me 600-650 to do it. is it a big job? or is it just ...

i have this annoying squeak coming from the front left had side of my 04 triton dual cab gls. i would almost pick it for a bearing noise except it doesnt increase as my speed does. it is bloody annoying. can anyone tell me where i might start looking before i take it in to a "mechanic". thanks

yeah. i think i will just try that. cheers

can anyone tell me the wire colours for the corresponding speaker? i have a 04 triton dual cab gls. thnaks

i currelntly have the 265 70 r16 on there. do i need to do any trimming of the gaurds? i hope not. i think i will put a body lift in and then go the bigger tyres. im in Albany West aust

i have done some looking around but i stil have a question about tyres. i am really keen on a set of 285 75 r16 cooper st's. the tyre tech guy nearly fell over and said no way will they fit. i have a 04 GLS triton dual cab. turb diesel. i havent done anything lift wise except for winding up the ...

hi. i have just bought a 04 triton 2.8 turbo diesel Gls dual cab. i want to do a 2 inch body lift for a simple lift for bigger tyres. is there anything i need to know before i do this? any probs i will encounter? can anyone point me in the direction of a online guide or give me some tips?

thankls ppl

can anyone tell me the tire size for a tyre say the equivilant of a 33 inch? im looking to put something onto a 15 inch rim so....is it 285/35? i know that is a fairly skinny tire.....just want to know wat is the biggest i can go on my 15x7 rims

ok. try this. this is a pic of the frame i have built so far. its not finished yet as you will be able to tell. overkill or not enough? it looks lop sided in the pic but it definately aint by measurements!

i was looking at what i have and i think i will weld a nice bit of thick steel plate over the top of the old seat base and drill my ne holes for the new sliders to bolt onto that. i will also cut the old sliding rails off the old bases. i think that would be a good way to go. hope fully wont be a ...

i was looking at what i have and i think i will weld a nice bit of thick steel plate over the top of the old seat base and drill my ne holes for the new sliders to bolt onto that. i will also cut the old sliding rails off the old bases. i think that would be a good way to go. hope fully wont be a ...

has anyone put race seats into their rovers before? i have an old 81 2 door rangie and have a set of race seats to put in. after looking at the original seat bases it looks like a mission and a half! anyone have any pointers on this?

just wondering. i am doing a rangie ute conversion to a tray back. i have built most of my cab frame but when i look at it it seems a bit over kill. is there any such thing as to much? has anyone got any pics of their frames they have made? i would post up a pic but i have no idea how to. i had a ...

im looking at doing a recore on my rangie radiator. its a 1981 2 door and i have recently swapped a 302 windsor into it. i was just wondering wat size radiator (core size) can i get to fit my original tanks? is aluminium better? would i be better off getting a whole new setup from say Aussie Desert ...

pull the spark plug out of number one and put your thumb over the hole. rotate the engine until you feel pressure on your thumb when you get this you are tdc. apparently

Rhino Buggies currently has this sweet looking ride. trying to convince my other half to let me have it.

http://www.rhinobuggies.com.au/new_page_2.htm

she says no............so not fair...........

im thnking i will go something fairly heavy duty. i had to remove the top part of the sill too...as in the floor on the drivers side. i dunno how it never collapsed when i was out 4wdin. the passenger side just needs the inner sill replaced right up to the body mount whereas the drivers side needs ...

thats good news about the sills! i was just havin a b1tch! i was thinkin along the same lines as you loand rangie about gettin the sills bent up. i need to replace the inner sheet that the body mounts attach to on both sides while the drivers sidf was completely stuffed. how did u have yours bent up ...

hahah nah not depressed........just want it to be finished!

omg i am gettin so sick of this car! i have put a new worked 302 in and a c4 auto, replaced a rear smashed diff, cut the rear off to make a ute. now i dunno what to do. i need to finish off the rear of the cab. but i dunno whether to keep the existing rear window (which i originally intended) or ...

does anyone know if aussie desert coolers make an oversized radiator to suit a rangie?i have recently put a bigger ford engine into my car and am worried about cooling it.

nice lookin machine! i am almost at the same stage on my ute conversion. i was goona buy an ol tray off a cruiser and cut it to fit. can you weld a tray to the chassis like that? will it pass engineering? haha go the ford engines. i just dropped a nicely work 302 windsor with a c4 auto into mine. i ...

i have heard that by changin a cog in my transfer case i can up the gearin so my car doesnt scream its nut off at 110 km/h...is this true?

hey dude. dunno if there is a kit for a tray back. i seen one somewhere for a well body type conversion. came with a fibre glass roof and all the other bits you need. i am currentl;y doin a tray back myself...just starting to put her back together at the moment. i found that its a learn as you go ...

hey dude. dunno if there is a kit for a tray back. i seen one somewhere for a well body type conversion. came with a fibre glass roof and all the other bits you need. i am currentl;y doin a tray back myself...just starting to put her back together at the moment. i found that its a learn as you go ...

speaking of 33 inch tires...will standard amge rover 10 spline diffs and axles hold up to 33's?

hey dude do you know what your gettin yourself into? tis yella_rnagie here from the perth site! like everyone says. you will love it then hate it and wanna write it off..then you will love it all over again.....happy roverin!

im just doin a ute conversion myself on a 81 2 door. thought i was just gonna take off the rear and attach a new tray... HA. at the moment it is totally stripped down. i found so much rust in the sills and the floor. then along came an unlicensed rangie with a 302 windsor conversion. so i had to ...