Outer Limits 4x4 Board

They are my son's & he is after about $1200 for the lot.

Thanks John , will give them a go.

It is a pity that you are in sunny Queensland as we are currently about to sell a 95 Disco chassis with GQ diffs,7 inch Lovell springs from an 80 series,long travel Remote Adjustable Tough Dogs , double cardin front drive shaft & modified rear one ,already done.They used Disco mounts & just welded ...

Hi all,I am chasing a set of spacers so we can attatch fuel injection to a P76 4.4 via a Thor manifold & assosiated stuff.Heres hoping someone out there can help. Thanks in advance,Steve.

Spot on pal!!!

hey mate what did the air filter box come out of?

thanx brett

No not quite,but the dash is the same.
Will post up pics ASAP.

Hi all, We just bought a Rangie & it is supposed to be a Wood&Picket conversion. The question is does anyone know what it is??? It has -Leather seats -Flares -Different motor(not 3.5 goes to well)with extracters,350 holley -Wood grain dash with extra gagues -2 tone paint -It's a 1/85 model,4 speed ...

today i got a letter from my insurance company telling me that i need to give them more money because my range rover is a panel van and has the potential to carry small goods.i rang them and they told me to ring the rta which didnt help me at all. has anyone else had this kind of trouble? my dads ...

Hi all,
Can you tell me the main differences between the 2 engines.
As fitted 2 discoverys.

Thanx Steve

Hi,
I've got an 95 3.9 auto Disco & get about 19-20 l/100kms
This is loaded with camping gear,also running 31's.

HTH
Steve

Hi all,
I have a 95 Disco & was wondering how difficult a 1 or 2 inch body lift is going 2 b ?

Will this clear 33's with 30mm spring lift?

Thanks Steve.

Hi DAS,
i had a spacer 4 the starter motor that i gave to steve to fit a 3.5 starter into a 4.4.
it was only about 3mm thick & went around the starter like a collar.

HTH Steve

Hi all,
would your opion witch springs would suit a 95 Discovery,they will
be 2 inches of lift,heavy duty

Thanks
Steve

Hi all, The best way to cure this problem is to cheat!!! Go to a Bike shop & get a push bike speedo, you can set tyre diameter up to 31 or 33 inches if you buy an expensive one,only goes up to 120kmh but thats enough. Fit to RHF wheel & run wires along brake hose into cabin[will need to extend wires ...

Hi,Just got a Disco myself.
AllFourx4Spares are excellant to deal with & PH [02] 49571117
HTH
Steve

Heres your answer!! Go to a bike shop {push}& buy a $15 speedo to fit a pushy. Glue the magnet on the inside of the wheel & fit pickup to backing plate. Extend wires into cab & program tyre size[some only go to 29 inches but most do 31 ] Super accurate & will go to 120 KMH witch is fast enough 4 a ...

It seems that in won't affect them enough to make a differance.
Will be easier to heat though.

Thanx again
Steve.

Hi All
Will I lose any strength in the front arms if I were to

A-Use heat to crank arms to required angle OR

B-Use a 100 ton press ?

Steve

Hi all, has anyone had any problems with the body/floor mounts cracking
when a body lift of 30 to 50 mm is installed?
Some Patrol & Cruiser drivers report this & the cost of repair is usually
$1000 + .

Thanks Steve.

i have King Springs & again no L/R difference.
It sits level But only 30 mm Of lift. 82 4 door.
But they are fairly heavy.

steve.

How much did the arms cost & did you fit a rear ball joint spacer?

Thanx Steve