So yer i have a 92 2.8d dual cab lux and it runs fine when its going, but the thing is an absolute pos to get going. Its okay if its on a flat bit of road, but if i have to start off on a decent incline i have to rev the nuts off it and ride the clutch to get it going. And this is without a load, if it had a load id have to go low range.
A good example of why this is shit, is if im backing a trailer in up my pretty steep driveway i have to go low range due its assness.
Are there any obvious reasons why it would be doing this? The only thing i can think of are the 31.5" tyres, but i wouldnt have thought this would cause any grief
:-P
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Issue with 2.8d performance (no not the usual issue)
Moderators: toaddog, Elmo, DUDELUX
Is it getting full throttle, ie the lever on the pump touching the stopper bolt.?
Tyres can knock power around, swap to some less aggressive smaller diameter tyres and see what happens.
Was i like this before you had work done?
Tyres can knock power around, swap to some less aggressive smaller diameter tyres and see what happens.
Was i like this before you had work done?
www.diesel-tec.com.au Ph 03 9739 5031
Ball bearing turbo upgrades for factory turbo vehicles. Got a diesel question just ask.
Home of the twin turbo shorty and many 150rwkw+ patrols.
Ball bearing turbo upgrades for factory turbo vehicles. Got a diesel question just ask.
Home of the twin turbo shorty and many 150rwkw+ patrols.
its been like this ever since i owned it, which is over a year, so yer it did it before i had the injectors done, and its not a bad batch of fuel again for the same reason
ive always wondered if it was a clutch issue but it doesn't slip at all so i sort of ruled that out, but you never know
i haven't checked if its getting full throttle, but as it was tuned when the injectors were done i'd expect this would be fine, ill check it out though, i do drive around with it at full throttle most of the time so i hope im getting as much as i can out of it ;-P
ive always wondered if it was a clutch issue but it doesn't slip at all so i sort of ruled that out, but you never know
i haven't checked if its getting full throttle, but as it was tuned when the injectors were done i'd expect this would be fine, ill check it out though, i do drive around with it at full throttle most of the time so i hope im getting as much as i can out of it ;-P
If you've had it for over a year did it get progressivly worse? The tyres wouldn't make you have to go low range to reverse a trailer. If it's your clutch is it slipping? There can only be a few reasons why a diesel is down on power, fuel, compression, or air. Check your air filter and see if there's a blockage in the air's path, check if you have the right fuel pressure. And then compression test it. Start cheap work your way up to the costly testing. Or you could stop being a tightarse get a mech/diesel mech to look at it.
hmm
yer it is blowing a bit of smoke, but not overly, getting the injectors done fixed this.
it hasnt got progressively worse, its just always been crap like this
its only underpowered at take off, its fine at other times
the mechanics didnt fix the issue thats why im asking here! ill just tell em to try harder next service i guess, maybe get em to check the clutch
yer it is blowing a bit of smoke, but not overly, getting the injectors done fixed this.
it hasnt got progressively worse, its just always been crap like this
its only underpowered at take off, its fine at other times
the mechanics didnt fix the issue thats why im asking here! ill just tell em to try harder next service i guess, maybe get em to check the clutch
Considering you can run 35's on a 2.8 and have no drastic (to your extent) power problems, 31's are are no probs, yeh, in this case i would just give it to a diesel mech, if you have checked all that you say you've checked, get it to a work shop m8, you dont wanna keep on driving it just incase it might escalate problems on you... my 2c, hope all goes well m8
Single cab 106r - BBP Turbo 3rz
*Boondal Backyard Performance*
*Boondal Backyard Performance*
I have come across some engines that have had simmilar issues when the cam jumped a tooth.
On the old VL 6cyl coms we used to advance the cam timing 1 tooth, and mod the dizzy to enable base idle timing to give them alot more go low down.
Im not sure if one tooth out will bend valves with the lux.
however if you have checked these things before, and the pump has been done, I would assume it was set up correctly and ok.
The govenor should prevent stalling when letting the clutch off slowly in 1st gear.
what did the diesel shop say about it when the pump/ injects were done??
I have found that little or no back pressure can affect the early take off from idle up to 1200rpm from either extractors, and or a leak in the exhaust.
When I patched up the flexi joint in mine, it gave back the low down rpm torque that it had lost before.
by what you describe, it sounds like the problem could be something else, but I thought I would offer some of my findings with simmilar probs.
Trains
On the old VL 6cyl coms we used to advance the cam timing 1 tooth, and mod the dizzy to enable base idle timing to give them alot more go low down.
Im not sure if one tooth out will bend valves with the lux.
however if you have checked these things before, and the pump has been done, I would assume it was set up correctly and ok.
The govenor should prevent stalling when letting the clutch off slowly in 1st gear.
what did the diesel shop say about it when the pump/ injects were done??
I have found that little or no back pressure can affect the early take off from idle up to 1200rpm from either extractors, and or a leak in the exhaust.
When I patched up the flexi joint in mine, it gave back the low down rpm torque that it had lost before.
by what you describe, it sounds like the problem could be something else, but I thought I would offer some of my findings with simmilar probs.
Trains
Save the Whales......Collect the whole set.
My Wife Can't Shear..............But You Should See Her Crutch !
My Wife Can't Shear..............But You Should See Her Crutch !
hmm
the injectors were screwed, the pump was fine so he redid the injectors and tuned it all up, he didn't mention the poor low down performance
one thing that you mentioned was the flex joint, mine does make a weird noise when i get to a certain rpm, the mechanic said its stuffed, maybe its causing some issues.
i just picked up some extractors off ebay and was going to get that fixed up when i go to the exhaust place, maybe that'll help
ill swap out the fuel filter as well as a check
the injectors were screwed, the pump was fine so he redid the injectors and tuned it all up, he didn't mention the poor low down performance
one thing that you mentioned was the flex joint, mine does make a weird noise when i get to a certain rpm, the mechanic said its stuffed, maybe its causing some issues.
i just picked up some extractors off ebay and was going to get that fixed up when i go to the exhaust place, maybe that'll help
ill swap out the fuel filter as well as a check
Who is online
Users browsing this forum: No registered users and 74 guests