Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Hi lux center bearing

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 287
Joined: Sun May 01, 2005 2:33 pm
Location: Sydney

Hi lux center bearing

Post by michael a »

Hi I have a hilux 85 model that keeps shitting the center bearing on the rear shaft how have other come around this problem.

1 peice shaft maybe
get under it
Top
Posts: 73
Joined: Wed Dec 13, 2006 5:21 pm

Post by Luxo »

One piece shaft is a realistic solution. However they dont chew out for no reason. Its generally caused by a bad uni joint or out-of-balance shaft. Do you have any vibrations? is it lifted? if so whats the pinion angle like?
I may be slow but I'm ahead of you!
Top
Posts: 287
Joined: Sun May 01, 2005 2:33 pm
Location: Sydney

Post by michael a »

it has about a 2in lift
get under it
Top
Posts: 145
Joined: Tue Feb 07, 2006 10:56 am

Post by muddylux »

Best thing I ever did was fit a one piece shaft, and the cost to get one made up using the original uni's and yokes was only $130. When you replace the centre bearing It would cost $90 just for the part and will only fail within 3-6 months.
They are only there to take vibration out and with a one piece you can't notice the differance, it is only a Hilux after al.l
Turn up th wick ya sook
Top
Posts: 478
Joined: Tue Jul 18, 2006 8:43 pm
Location: outer east Melb.

Contact:
Contact MUD EMPIRE

Post by MUD EMPIRE »

muddylux wrote:Best thing I ever did was fit a one piece shaft, and the cost to get one made up using the original uni's and yokes was only $130. When you replace the centre bearing It would cost $90 just for the part and will only fail within 3-6 months.
They are only there to take vibration out and with a one piece you can't notice the differance, it is only a Hilux after al.l
I would have-to agree with muddylux, good advice. Only thing is
that I've had mine lifted (drivetrain, springs) 3 inches for 2 to 3
years and never replaced a centre bearing and it's as smooth
as silk..........go figure!
Top
Posts: 361
Joined: Sat Mar 06, 2004 11:09 pm
Location: Western Australia

Contact:
Contact toyrex

Re: Hi lux center bearing

Post by toyrex »

michael a wrote:Hi I have a hilux 85 model that keeps shitting the center bearing on the rear shaft how have other come around this problem.

1 peice shaft maybe
The el cheapo only last about 4 month, genuine Toyota last alot longer but you pay for them
I have been fitting one piece shafts on all my conversions for about 18 years now
Adrian
www.chevtorque.com.au
Top
Posts: 2404
Joined: Fri Jul 07, 2006 9:00 pm
Location: Ipswich

Post by Sic Lux »

Thats it don't piss around as with the lift it put's to much angle on them i also run a Double cardin in my rear shaft think it's supposed to help with uni wear/angle they run at.
As soon as we lifted mates lux 2in about a week later it started floging out it's soon to be a 1 peice shaft :armsup:
plenty of parts on the bench
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 1 guest