Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

80 Series Heater controls

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 522
Joined: Sat Jan 29, 2005 7:40 am
Location: Melbourne, Vic

80 Series Heater controls

Post by Toy80Diesel »

This may be more of an elec question, but I have problems removing the trim etc.... the globe is the easy part.

Its a 96 cruiser. I need to change the illumination globe behind the fan/heat controls as its blown. The problem I have is how do I get the control facia off. I cant see how to remove the AC button so I can get to the globes. I don't want to break the switch so I thought I'd ask before I attempt it. The levers just have rubber/plastic ends that slide off and the control panel, from memory, has four screws holding it. But the AC button wont let go.

Thanks
Shut Up, Get Out, & Start Digging...
Top
Posts: 2097
Joined: Tue Aug 12, 2003 6:50 pm
Location: wollongong

Post by dow50r »

the ac button pulls out as a push in switch...
Top
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

dow50r wrote:the ac button pulls out as a push in switch...
And can be a real PITA to get moving. You need a small screwdriver and just get it under the edge of the small black surround on the switch and try and leaver it out gently. There is no clip or anything they just push in.
Top
Posts: 780
Joined: Wed Apr 26, 2006 7:11 pm
Location: darwin again

Post by simkell »

are you having trouble getting the facia out or sepperating the heater control from the facia. i thought once the facia was removed the globe was easy to get to. i'll check my manual! :roll:
MUD, MUD, GLORIOUS MUD!
Top
Posts: 522
Joined: Sat Jan 29, 2005 7:40 am
Location: Melbourne, Vic

Post by Toy80Diesel »

simkell wrote:are you having trouble getting the facia out or sepperating the heater control from the facia. i thought once the facia was removed the globe was easy to get to. i'll check my manual! :roll:
Its just the facia that needs to come out for me to replace the globe. But the AC button seems to stop it from coming out.

Thanks everyone for your comments, I'll give it a try.
Shut Up, Get Out, & Start Digging...
Top
Posts: 780
Joined: Wed Apr 26, 2006 7:11 pm
Location: darwin again

Post by simkell »

the facia has two screws behind the ashtray and two screws behind the slot in the top left corner. then it is just held in by clips. pull facia out.
the a/c botton shouldn't affect it coming out. hope this helps
MUD, MUD, GLORIOUS MUD!
Top
Posts: 522
Joined: Sat Jan 29, 2005 7:40 am
Location: Melbourne, Vic

Post by Toy80Diesel »

simkell wrote:the facia has two screws behind the ashtray and two screws behind the slot in the top left corner. then it is just held in by clips. pull facia out.
the a/c botton shouldn't affect it coming out. hope this helps
Sorry, maybe you are confusing which facia. The large one is the easy part, I'm talking about the one with just the heater/fan/ac controls.
Shut Up, Get Out, & Start Digging...
Top
Posts: 204
Joined: Wed May 25, 2005 6:18 pm
Location: Karratha Western Australia

Contact:
Contact shanegtr

Post by shanegtr »

AC switch should come out the same as any other switch / switch blank that is in the dash, just get a small flat blade screwdriver and lever it out
80 Series forum
www.offroad80s.com
Top
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

So how did you go? I just had the entire dash out of mine. Right back to the firewall. Only thing left was the wiring harness. Never let a rat build a nest in your heater box :bad-words: :bad-words: Had to replace all the Ducting,HeaterBox,AC box and Blower motor assembly. Rat had eaten holes in all these. But had not touched the wiring at all.

After puting it all back together tonight i noticed the light in the top half of the heater controls doesnt work but im not pulling it back out again. Even once you get the facia off getting the control panel out is a job in its self. Im not even sure you could get it out without pulling the entire dash. And even then the globes are in a PITA spot to get to.

For those who havent read anything about the 80 i bought it came from an Auction and had been stored for 2 years before being Auctioned with a window down and a rat found its way inside and decided to nest in the dash.
Top
Posts: 522
Joined: Sat Jan 29, 2005 7:40 am
Location: Melbourne, Vic

Post by Toy80Diesel »

RUFF wrote:So how did you go?

After puting it all back together tonight i noticed the light in the top half of the heater controls doesnt work but im not pulling it back out again. Even once you get the facia off getting the control panel out is a job in its self. Im not even sure you could get it out without pulling the entire dash. And even then the globes are in a PITA spot to get to.
Haven't attempted it yet, but I don't want to take out everything. I won't be disconnecting the cables, just want enough room to get my hand in there to change the globe. I'll post it up once I'm finished, but probably won't be until the weekend.

Thanks for the advice
Shut Up, Get Out, & Start Digging...
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 1 guest