Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
factory diff locker wont engage
Moderator: -Scott-
factory diff locker wont engage
i havent used it for about 1 month because it has been sitting in the shed but when i put it there it was fine and now it wont lock in .. the light on the dash wont even flash ... i have checked all my fuses and the plugs and good .. why is it doing this can anyone help ???
not sure, try locate the compressor in the rear on the passenger side i think.. i never actually looked for mine, it worked without any probs.
once u find it try conecting power directly to it and see if it works like that
once u find it try conecting power directly to it and see if it works like that
my GUBanzy wrote:Dial up internet.........you'd post something and come back 2 beers later to see if it loaded.
It's hidden in the left rear wheel arch, on the forward side of the arch. I think there's an access panel inside the cabin, on top of the arch.
Otherwise, just trace the hose coming out of the diff to where it ends up forward of the left rear wheel.
It sounds to me like your switch in the dash may be the problem though. Either that or the locker's "ecu" harness (it has it's own little doo-dad to control the lights and only lock when in 4Lo). I think this is located nearby to the compresor???
Otherwise, just trace the hose coming out of the diff to where it ends up forward of the left rear wheel.
It sounds to me like your switch in the dash may be the problem though. Either that or the locker's "ecu" harness (it has it's own little doo-dad to control the lights and only lock when in 4Lo). I think this is located nearby to the compresor???
[color=blue]blue swb gls 3.0 wanker[/color]
You should also check the rear Diff detection switch plug on top of the diff, and and also where it connects into the main wiring loom above the left rear trailing arm.
If you are not getting any compressor activation, then you need to check back to the Compressor and the ECU. Both of these on a SWB are in behind the lining on the left hand rear side. To get into there you will need to unbolt the two lower bolts of the left front and rear seat belts, if I remember in behind the rear ashtray there is a screw(s) to remove, then remove any of the plastic plugs that hold the lining on, and move the complete lining away from the side. You may have to remove a rear seat.
The ECU is mounted just below the rear window in about the middle. The compressor is around there somewhere also (forward of ECU but very close).
Once you have accessed the compressor/ECU, you should be able to put a meter onto the wiring right through.
I can send you a rear diff lock wiring diargam for 3.0/3.5L, but not the 2.5L, however I suspect they will be very similar. PM me if you need this.
If you are not getting any compressor activation, then you need to check back to the Compressor and the ECU. Both of these on a SWB are in behind the lining on the left hand rear side. To get into there you will need to unbolt the two lower bolts of the left front and rear seat belts, if I remember in behind the rear ashtray there is a screw(s) to remove, then remove any of the plastic plugs that hold the lining on, and move the complete lining away from the side. You may have to remove a rear seat.
The ECU is mounted just below the rear window in about the middle. The compressor is around there somewhere also (forward of ECU but very close).
Once you have accessed the compressor/ECU, you should be able to put a meter onto the wiring right through.
I can send you a rear diff lock wiring diargam for 3.0/3.5L, but not the 2.5L, however I suspect they will be very similar. PM me if you need this.
1994 NJ SWB, 3.5L V6, 5sp manual, 3.15 low speed gears. 4.9 diffs, Factory rear locker, ARB Front Locker,
35" Mudzillas, 2" body lift, 2" suspension lift, Safari snorkel, Warn 8274 High Mount
35" Mudzillas, 2" body lift, 2" suspension lift, Safari snorkel, Warn 8274 High Mount
Not sure what the second ECU is, maybe electronic suspension (if you have it).
If compressor is fine, then you need to check all plug connections as mentioned. Then recheck the locker switch, then the ECU (not sure how ?)
Otherwise you may have a wiring break.
If compressor is fine, then you need to check all plug connections as mentioned. Then recheck the locker switch, then the ECU (not sure how ?)
Otherwise you may have a wiring break.
1994 NJ SWB, 3.5L V6, 5sp manual, 3.15 low speed gears. 4.9 diffs, Factory rear locker, ARB Front Locker,
35" Mudzillas, 2" body lift, 2" suspension lift, Safari snorkel, Warn 8274 High Mount
35" Mudzillas, 2" body lift, 2" suspension lift, Safari snorkel, Warn 8274 High Mount
yes all the other lights work correctly when locking into differnt 4x4's .. could of my body lift have disconnected something or snapped a wire ?? although i cant see anything broken or disconnected has it happened before ?? because it hasent worked since i done my body lift now i think about it !!!
Who is online
Users browsing this forum: No registered users and 25 guests