Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Bending 4.0mm x 42.00mm tube..

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 936
Joined: Fri May 26, 2006 4:31 pm
Location: Sunshine Coast, QLD

Post by Mulisha »

Thanks alot guys i think i'll give dave a ring tommrow or something to see what we can come up with..

Thanks for ya help and yeah the more i imagine that bar i was thinking of making the worse it will look :roll: :roll:

Cheers

Rick.
Top
striker99
Banned
Posts: 382
Joined: Sat Apr 21, 2007 3:50 pm
Location: Brisbane

Contact:
Contact striker99

Post by striker99 »

Shorti wrote:
striker99 wrote:Try contacting you local hardware store and ask them to do it bunnings wearhouse would most likely be a good one if theres one near you.
Bunnings don't do anything like that...
Righto was just a guess since they sold alot of steel
Top
Posts: 378
Joined: Tue Nov 02, 2004 8:54 pm
Location: blue mountians

Post by superzuki »

i bent 42mm pipe with 4 mm walls with a supercheap hudraulic bender...



Image


Image
Top
Posts: 1897
Joined: Thu Aug 05, 2004 6:24 am
Location: of the best barwork is at www.bolsys.com.au

Post by 80lsy gq »

superzuki wrote:i bent 42mm pipe with 4 mm walls with a supercheap hudraulic bender...



Image


Image
good work...

tip for you for next time..if you want to eliminate the little dents inj the tube where it sits on the rollers get some 40nb tube about 100mm long and cut it in half..place it over the tube between the tube you are bending and the rollers..it will spread the load and wont kink your tube...i actually used to have two pieces welded to the rolers...worked good and i did heaps of bends with it..

dave
www.bolsys.com.au

the original and the best
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

That sounds like a good idea , might try that , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 1897
Joined: Thu Aug 05, 2004 6:24 am
Location: of the best barwork is at www.bolsys.com.au

Post by 80lsy gq »

:D :finger:
www.bolsys.com.au

the original and the best
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

Be my friend ,Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 936
Joined: Fri May 26, 2006 4:31 pm
Location: Sunshine Coast, QLD

Post by Mulisha »

Nice bar ... time to start on ya sliders :lol: :lol: :lol: :D
Top
Posts: 671
Joined: Mon Aug 23, 2004 10:06 am
Location: Mornington

Post by YankeeDave »

why build a bar that dosnt have capabilities for a winch :?
Jeep Wrangler TJ

Jeep Cherokee XJ
Top
Posts: 936
Joined: Fri May 26, 2006 4:31 pm
Location: Sunshine Coast, QLD

Post by Mulisha »

YankeeDave wrote:why build a bar that dosnt have capabilities for a winch :?
Maybe he doesn't plan on getting stuck :finger: :D
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 1 guest