Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

warn 8274 brake sharft spindle

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 37
Joined: Mon Jun 07, 2004 10:44 pm
Location: s/w vic

warn 8274 brake sharft spindle

Post by old tom »

HI has any one had truble taping into the end of brake sharft? broken 3 taps any iders ?
Top
Posts: 469
Joined: Fri Sep 10, 2004 1:45 pm
Location: Melb

Post by sootygu »

Had the same problem. HSS would not touch it so ended up using carbide taps but even broke a couple of those, luckily they cost me nothing.

Carbide is probably your only option.
Top
Posts: 37
Joined: Mon Jun 07, 2004 10:44 pm
Location: s/w vic

Post by old tom »

what would happen if i over drilled the hole and then mig the hole then taped into it would this work?
Top
Posts: 1232
Joined: Sun Feb 29, 2004 11:37 pm
Location: Brisvagas

Post by Bad JuJu »

Cobalt tap - is apparently what you use.
Posting quality not quantity!

Wanted: Stock HiLux Front Leaf Springs
Top
Posts: 783
Joined: Sat Jul 09, 2005 6:57 pm
Location: geelong

Post by GQ4.8coilcab »

Me and the old man had trouble drilling it. What bit did you use? And yer, what tap do you use? Is it absolutely necessary? We gave up but havent fitted it yet so we can still do it. Any hints?
[color=red][size=150][b]CTRL + W[/b][/size][/color]
Top
Posts: 1094
Joined: Tue Feb 10, 2004 6:58 pm
Contact:
Contact STIKA

Post by STIKA »

i have had a bolt tig welded to mine
Supported By
Milanco
Phones N Alarms
Buds Customs
Top
Posts: 783
Joined: Sat Jul 09, 2005 6:57 pm
Location: geelong

Post by GQ4.8coilcab »

STIKA wrote:i have had a bolt tig welded to mine
mmmmm good idea :cool: Wouldn't be as strong as tapping a bolt but will hold it better then the circlip anyday
[color=red][size=150][b]CTRL + W[/b][/size][/color]
Top
Posts: 574
Joined: Wed Aug 17, 2005 11:49 am
Location: NZ

Post by nzdarin »

I've had a clamp made that fits over the circlip. To fit it you need to remove the circlip and the spring washers. It then fits where the spring washers were. You then put the circlip on and then the second part has a recess machined into it that the circlip fit into. There are 3 bolts that hold the 2 parts together.
A little bit more involved puttig it together BUT it will fit any standard winch without mods!
93 Nissan Pathfinder / Terrano Turboed VH45, GQ Trans and T-case, coil overs, hydraulic winch and fair bit of other stuff. (Currently a pile of parts in the workshop)
Top
Posts: 214
Joined: Sun Jul 06, 2003 4:02 pm
Location: WA

Post by Zac Zec »

any good machine shop should be able to drill and tap it. cost me 100 bucks to get my done(bolt and end cap machined out of 4140 included).
They drilled the hole with like a masonary drill bit(slighty different) then heated up to tap it, then treated it again to bring it back to strength.
Money well spent i rekon

Cheers
Top
Posts: 3064
Joined: Sun Jun 12, 2005 11:00 pm
Location: Yinnar South, Vic

Contact:
Contact cloughy

Post by cloughy »

Zac Zec wrote: They drilled the hole with like a masonary drill bit

Cheers
:?
Wanted: Car trailer or beaver tail truck, let me know what you got
Top
Posts: 93
Joined: Mon Jul 12, 2004 9:24 pm
Location: western district

Post by jaspers joint »

If you sharpen a masonary bit the same as normal drill it will drill thru hardened steal
Top
Posts: 722
Joined: Sat Nov 09, 2002 9:31 pm
Location: Berwick, Melbourne

Post by awill4x4 »

jaspers joint wrote:If you sharpen a masonary bit the same as normal drill it will drill thru hardened steal
also, if you reverse sharpen a masonry bit and run it in reverse in a drill at slow speeds it will often drill out a snapped HSS tap that can't be removed normally.
Regards Andrew.
We are Tig welders, gravity doesn't worry us.
[img]http://www.studmonkeyracing.com/forums/smilies/weld.gif[/img]
Top
User avatar
Guy
Posts: 10366
Joined: Thu Dec 12, 2002 8:43 am
Location: Wangaratta

Post by Guy »

I have used and abused a set of drill bit made by a german mob, they are labelled Allround Bohrer .. Picked them up from a 4x4 show years ago. After watching the guy turn a wiltshire file into swiss cheese with one bit (about 30 holes) and start on another as a demo I was convinced. I have never sharpened mine and they still bite well. Work as masonary bits as well ..
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Top
Posts: 3064
Joined: Sun Jun 12, 2005 11:00 pm
Location: Yinnar South, Vic

Contact:
Contact cloughy

Post by cloughy »

jaspers joint wrote:If you sharpen a masonary bit the same as normal drill it will drill thru hardened steal
No shit, you sharpen the little endy bit as per normal drill bit :?:
Wanted: Car trailer or beaver tail truck, let me know what you got
Top
User avatar
Guy
Posts: 10366
Joined: Thu Dec 12, 2002 8:43 am
Location: Wangaratta

Post by Guy »

cloughy wrote:
jaspers joint wrote:If you sharpen a masonary bit the same as normal drill it will drill thru hardened steal
No shit, you sharpen the little endy bit as per normal drill bit :?:
Make sure that you have an aluminiom oxide stone or similar to sharpen it with, and that the bit is of good quality to begin with .. not all carbide tips are equal
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Top
Posts: 214
Joined: Sun Jul 06, 2003 4:02 pm
Location: WA

Post by Zac Zec »

You can buy special drill bits that look like a masonary bit just to drill high tensile and hardened steel.
Top
Posts: 3064
Joined: Sun Jun 12, 2005 11:00 pm
Location: Yinnar South, Vic

Contact:
Contact cloughy

Post by cloughy »

Zac Zec wrote:You can buy special drill bits that look like a masonary bit just to drill high tensile and hardened steel.
Deadset?? not taking the piss, very curious indeed, do you have any links, pics??
Wanted: Car trailer or beaver tail truck, let me know what you got
Top
Posts: 214
Joined: Sun Jul 06, 2003 4:02 pm
Location: WA

Post by Zac Zec »

Deadset :!:
Top
Posts: 1857
Joined: Fri Feb 02, 2007 12:16 am
Location: ipswich

Post by nastytroll »

The brand I have used is ARTU drill have been using them for 12 years (not the same ones), they can be sharpened to an extent if you have a diamond lap/wheel. I used to use them for drilling upto 62 rockwell hardend alloy toolsteels and tungsten molibdenum high speed steels, A file is only 56-58 rockwell. They need to be kept cool or the silversolder will melt holding the carbide tip in and if they get exesive vibration the will chip.
ARTU drills are cheap bout $6 for a 10mm.
Back to topic highmount brake shafts are only case hardend so you can anneal the end to be tapped, The late model warn shafts have a deeper hardening and some I've tryed to tap were to hard so I drilled them oversize pressed in a hightensile slug and tig welded it in then tapped the slug. I've done prob 30 Highmount brake shafts and had no problems.
Top
Posts: 782
Joined: Tue Mar 08, 2005 12:03 pm
Location: brisbane

Post by giantracing »

easy job. 10mm hole 20 mm deep. $100 per sharft . done heaps of them never had one i couldn't do.
build em tuff, drive em ruff.........

Custom 4wd Creations Brisbane
0438279890
Top
Posts: 783
Joined: Sat Jul 09, 2005 6:57 pm
Location: geelong

Post by GQ4.8coilcab »

giantracing wrote:easy job. 10mm hole 20 mm deep. $100 per sharft . done heaps of them never had one i couldn't do.
how do you do it :lol:
[color=red][size=150][b]CTRL + W[/b][/size][/color]
Top
Posts: 782
Joined: Tue Mar 08, 2005 12:03 pm
Location: brisbane

Post by giantracing »

easy. deposit 100 in to an account. post to me, i do it, send it back. see easy for you
build em tuff, drive em ruff.........

Custom 4wd Creations Brisbane
0438279890
Top
Posts: 59
Joined: Thu May 10, 2007 3:31 pm
Location: Geelong

Post by chpd 80 »

Anyone in Melbourne who does this???
Top
Posts: 309
Joined: Wed Nov 08, 2006 7:11 am
Location: newcastle

Post by hammey »

chpd 80 wrote:Anyone in Melbourne who does this???
yeah mate, SG Leslie&sons ph 0394592859
19 Mologa rd West Hiedelberg
VIC 3081

The guys name is Malcom. cost me $80 and you get a bolt as well as the retaining cap, and maybe shims but cant remember. :D
innovation is better, better is faster, and fast is all that counts
Top
Posts: 37
Joined: Mon Jun 07, 2004 10:44 pm
Location: s/w vic

Post by old tom »

sent mine to malcom today
Top
Posts: 59
Joined: Thu May 10, 2007 3:31 pm
Location: Geelong

Post by chpd 80 »

Thanks guys, will send it to them today.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 151 guests