Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
bodylift
Moderators: toaddog, Elmo, DUDELUX
Depending on who you talk to, The clutch line mount needed to be inverted on my petrol one. Not sure about the diesel.
Otherwise most of the stuff on the lux will stretch enough that you don't need to worry about it.
Otherwise most of the stuff on the lux will stretch enough that you don't need to worry about it.
1988 Hilux, 4y, 2 inch Lift Superior Engineering, Custom Tray.
Tamworth Team Penning Association.
Tamworth Team Penning Association.
Loosen steering shaft off under the dash before it's lifted and read here http://www.outerlimits4x4.com/phpBB2/vi ... p?t=126923 loosen radiator hoses and twist to the right angle once lifted the do up bend the clutch line on where it mounts to the body not hard to do take gearbox boot and plate off cut the centre bit out of the plate between the two sticks check with this back on it may need more triming just depends to solve this you can also bend gearsticks to get it right i know on diesels check your booster lines from the vacuum pump had 2 mate's there's came off one at airlocker ave cruiser park. may need to remove/cut lower bit of radiator sheild just check the fan has some clearance and allow for some movement. in general have a look and feel foses pipes wire's before and after and try ge tthem to match so there not under anymore stress
plenty of parts on the bench
Had to lift the 4runner today to fit some Baja claws under the guards. (they wouldn't fit on my other car)
First off, rp7 or crc all the nuts for the mounting points (10)
Then go around with 2 sockets sitting one on top of the mounting bolts to hold it and undoing the bottom one along one side
Loosen the nuts along the other side but don't take them off.
Undo the top and bottom bolts on your steering shaft and loosen the 3 holding the mount to the firewall under the dash.
Jack up one side of the body (not the chassis, lol) using the method of your choice, i would recommend anything EXCEPT the way i used today for obvious reasons haha.
Starting at the front slip all the bolts out and retain all rubber bushes, slip in the new mounting spacers.
Repeat all along the body then leave nuts loose and repeat on the other side.
Once they are all done, tighten them like you would do with a wheel, diagonal opposites first to ensure it settles properly.
go back to your steering rack and ensure the shaft is deep enough top and bottom just loosen both bolts and slide the shaft until it's deep enough in the clamps, after playing around for 10 mins i have about 20mm top and bottom.(not like this, this is what it looks like before adjusting.
BEWARE OF REDBACKS, i had to flame thrower a whole family of them today with a lighter and some RP7 while i was working on the lift, they seemed to like living in my chassis and engine. ( you can see the burned carcas of one in this pic)
Tighten everything back up and ta-da - 55mm more lift on your body for 2 hours work.
I think it was the most rewarding 2 hours of the build so far.
The bullbar is only on as a test fit and still hasnt had a final coat, the new engine still hasn't gone in, when it does i'll be raising the bullbar up as high as possible with a new bracket.
First off, rp7 or crc all the nuts for the mounting points (10)
Then go around with 2 sockets sitting one on top of the mounting bolts to hold it and undoing the bottom one along one side
Loosen the nuts along the other side but don't take them off.
Undo the top and bottom bolts on your steering shaft and loosen the 3 holding the mount to the firewall under the dash.
Jack up one side of the body (not the chassis, lol) using the method of your choice, i would recommend anything EXCEPT the way i used today for obvious reasons haha.
Starting at the front slip all the bolts out and retain all rubber bushes, slip in the new mounting spacers.
Repeat all along the body then leave nuts loose and repeat on the other side.
Once they are all done, tighten them like you would do with a wheel, diagonal opposites first to ensure it settles properly.
go back to your steering rack and ensure the shaft is deep enough top and bottom just loosen both bolts and slide the shaft until it's deep enough in the clamps, after playing around for 10 mins i have about 20mm top and bottom.(not like this, this is what it looks like before adjusting.
BEWARE OF REDBACKS, i had to flame thrower a whole family of them today with a lighter and some RP7 while i was working on the lift, they seemed to like living in my chassis and engine. ( you can see the burned carcas of one in this pic)
Tighten everything back up and ta-da - 55mm more lift on your body for 2 hours work.
I think it was the most rewarding 2 hours of the build so far.
The bullbar is only on as a test fit and still hasnt had a final coat, the new engine still hasn't gone in, when it does i'll be raising the bullbar up as high as possible with a new bracket.
Last edited by Sketch on Thu Dec 13, 2007 7:05 pm, edited 5 times in total.
Resident Terrorist
haha, i'll do it at half that price bargainRAY185 wrote:Did someone actually quote you that much to do a body lift on a hilux?moto maniac wrote:if its sooooooo easy (i think i can even do it! - and will) then why do shops charge upwards fo $1600 to do a body lift??? especially seeing as though parts are what only $200 max!
The tubes are in there just cant really see em in the pics,Sic Lux wrote:Yeah same i'll supply everything for that price and a cartoon in the back as apreaciation of your business
Just a Q for Shetch why no crush tube or am i blind and love the jack set up i normaly just use a 4x2 off cut on the jack.
haha yeha i've done dodgier but that jack setup was a stroke of genius (it also nearly broke my toe haha)
the suspension lift will have to wait untill the engine goes in as i rolled it out of the garage today and it took a stripe of paint off the roof
that there is a pretty good example of how easy it is and how much money u can save by doing yourself. if fitted 33 bighorns on my 4 runner 2inch suspension and 2 body and only just srubb. mabey a 3inch body would clear them but anyway. i would definatly give it a go yourself it is much easier that you may think and will save u a fair bit of money.
Who is online
Users browsing this forum: No registered users and 10 guests