Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Boring out TB42 to 4.5L

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Post Reply
Posts: 120
Joined: Mon Jan 02, 2006 6:37 pm
Location: Wanneroo WA

Boring out TB42 to 4.5L

Post by Brett S »

Going to rebuild 4.2 in not too distant future and if reboring may as well go out to stock 4.5L piston size so:
Are the blocks thick enough to go out to 99.5mm?
Do the heads have same valve design and therefore same valve pockets in piston?
What is the stock compression ratio of tb42 and tb45, as might have to turn down pistons a bit so not as to have excessive compression ratio.
Any one done it?
Oh and yes I have searched.
Diesel is for tightarses
Posts: 4275
Joined: Fri Nov 22, 2002 6:41 pm
Location: Western Australia

Post by Hoonz »

would be cheaper and reliable to buy a 4.5 petrol engine and install
H( * )( * )NZ loves B( * )( * )BIES
if a fat lady falls in the forest do the trees laugh?
[quote="RUFF"]although i didnt mean to, i squealed like a girl :armsup:[/quote]
Posts: 1644
Joined: Thu Aug 03, 2006 9:50 pm
Location: Hawkesbury, Sydney

Post by CWBYUP »

Hoonz wrote:would be cheaper and reliable to buy a 4.5 petrol engine and install
My thoughts exactly.

Nick
[quote="Vulcanised"]more grunt than a row of drunk girls at a B&S ball!
[/quote]
Posts: 300
Joined: Sun May 20, 2007 2:22 am
Location: Toowoomba QLD

Post by 90Mav »

no idea about wall thickness. im thinking standerd oversize pistons would be a better option, you would have to look at them side by side i suppose..
bear in mind that increasing bore will increase compression. you could also get some displacement increase by offset grinding the crank, and using undersize bearings, or even diffrent rods. fair bit of homework to do this sort of stuff..
Thrashed '90 Leaf spring Maverick ute, TD42, 2" EFS lift. 36 Swampers.
Posts: 120
Joined: Mon Jan 02, 2006 6:37 pm
Location: Wanneroo WA

Post by Brett S »

Buying a 4.5 injected would not be a cheaper option:
have to buy another complete motor that has already done many k's, convert fuel system to efi and change licensing engine numbers with a possible trip over the pits.
I have the 4.2 already and should be able to rebuild it for $1600ish so it would be as new not 150000k's on it.
And i am happy to turn down the crown of 4.5L piston to get usable compression ratio.
Stroking not overly keen on due to having to play with rod lengths and possible block/rod clearancing issues.
Diesel is for tightarses
Posts: 897
Joined: Tue Aug 02, 2005 2:31 am
Location: Central Coast

Post by MyGQ »

the TB45 uses the same TB42 block, from memory they didn't change anything apart from the bore and stroke. TB42's can be bored out for the 4.5L specs, have a look at a Gregories manual for the petrol GU and see what it says in regards to bore and stroke, its not that much different from the TB42.
AA's for Quitters
Posts: 1258
Joined: Wed Mar 21, 2007 7:49 pm
Location: Mornington/ Victoria

Post by PGS 4WD »

TB42 and TB45 have the same stroke, the 0.3 L comes from bore only, I doubt the performance difference has anything much to do with the extra capacity but more the higer lift camshaft and better cylinder head and manifold design. I have fitted camshafts and done a little head work with aftermaket tuneable EFI and the output power is as good as the TB45, and all the way down to idle.

Joel
-Pre trip inspections/ servicing
-Suspension/ custom modifications
-4wd Dyno & tuning
-Qualified mechanics
Posts: 5
Joined: Wed Jul 11, 2007 8:51 am
Location: Melbourne

Post by fwnsp »

hi mate,
i reckon you'd be better off rebilding a tb42 as a tb42 or buy a wrecked tb45 and rebuild that one.

i'm pretty sure they are the same block, but a lot of stuffing around just for the sake of 0.3L
Posts: 24
Joined: Thu Apr 12, 2007 10:46 am
Location: newcastle

Post by bigorangetruck »

G`day mate,new to this site,but here something for you,rebuild your tb42 bottom end,fit a tb45 top end.they bolt straight on,and with a aftermarket computer,they go verywell and improve drivability heaps.I`ve just done this to my comp ute(plus a turbo & intercooler),but bought the bits on ebay and cost less than a $1000.All the exhaust bolt up like factory
Posts: 120
Joined: Mon Jan 02, 2006 6:37 pm
Location: Wanneroo WA

Post by Brett S »

So if the head bolts onto a 4.2 bottom end with 4.2 pistons that must mean that both heads have the same combustion volume and therefore it must be the pistons that compensate to make the compression ratio the same.
Would a carby inlet manifold bolt up to a 4.5 head? as i heard the 4.5 has bigger and better ports.
Diesel is for tightarses
Posts: 24
Joined: Thu Apr 12, 2007 10:46 am
Location: newcastle

Post by bigorangetruck »

Yeh mate,the compression ratio isnt affected with a tb45 head,but you cant run the carby and manifold from a 42 cause it`s a completely different pattern,but the exhaust patern is the same.there is other difference like the water plumbing,the factory hoses dont just go on from either model,but a metre of water hose,and we made our own.
Posts: 897
Joined: Tue Aug 02, 2005 2:31 am
Location: Central Coast

Post by MyGQ »

If you do what your doing look at Straight Gas for the buggar

then u can use the TB45 head and inlet chamber to control the gas flow, get a 4.5L engine out of it and run it cheaper.
AA's for Quitters
Post Reply

Who is online

Users browsing this forum: No registered users and 160 guests