Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
What to "soak" AFM in?
Moderators: toaddog, TWISTY, V8Patrol, Moderators
What to "soak" AFM in?
My AFM needs a good clean, contact cleaner didn't do the job and I know of someone who took their prado to a toyota dealership who apparently soaked his AFM which brought it back to spec increasing power which by all means should bring economy back.
So what to "soak" the AFM in is the question considering it is cased in plastic.
So what to "soak" the AFM in is the question considering it is cased in plastic.
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
I put a whole can of carby cleaner through it today until the writing was off the stickers and the rubber seal went soft. I put it back in with some silastic just incase air has been aso getting past the seal.
I might be joshing myself but it feels kinda different, doesn't seem to take as much right boot to get off the line or sit at the speed limit
No power difference when I put the pedal to the floor though
I might be joshing myself but it feels kinda different, doesn't seem to take as much right boot to get off the line or sit at the speed limit
No power difference when I put the pedal to the floor though
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
That's about how mine felt after cleaning. Full throttle not a great deal difference, but response in the first half of the throttle improved noticably. Also a lot smoother in the gear changes.high n mighty wrote:I might be joshing myself but it feels kinda different, doesn't seem to take as much right boot to get off the line or sit at the speed limit
If God did not intend for us to eat animals, then why did he make them out of meat?
I also noticed that the near new air filter was filled with sand. I guess the snokel must be right in the line of fire unlike my lux....
I will replace it though the week, if memory serves me the 17ltr per hundred was just after I put this filter in.
Don't get me wrong, it is still very free flowing but I will throw one in and see if it comes down again
I will replace it though the week, if memory serves me the 17ltr per hundred was just after I put this filter in.
Don't get me wrong, it is still very free flowing but I will throw one in and see if it comes down again
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
CRC make a specific cleaner for a MAF.
CRC MAF Cleaner
Have no idea if it works or is advisable to do but ....
CRC MAF Cleaner
Have no idea if it works or is advisable to do but ....
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
X2mud4b wrote:HotFourOk wrote:Just soak it in petrol, then metho to dry it out
i hope your joking?
As joel said, Carby clean is fine. Or a carbon/throttle body cleaner. You shouldn't need to 'soak it' and it would probably be a good idea not to 'soak' the eletrics. All you need to do is clean the hot wire in the middle of the sensor. DONOT attempt to touch or wipe the hot wire. just spray.
The AFM will work for partial throttle applications, most Engine management systems have predetermined values for Wide Open Throttle (WOT) application and hardly rely on AFM response as economy is not an issue if your driving WOT so injector pulse and ignition timing will increase to predetermined values and things like AFM and O2 sensor become asthetic pretty much.
That explains why you may notice an improvement in throttle response from start off etc.
Cheers Dan
[quote="Uhhohh"]As far as an indecent proposal goes, I'd accept nothing less than $100,000 to tolerate buggery. Any less and it's just not worth the psychological trauma. [/quote]
So you are saying that even if it feels like it has made a difference the fuel usage won't have changed?? Just a reference note, the wire isn't clearly visible on a prado afm, I'm no mechanic but I havent seen such an enclosed one before.Ruffy wrote:X2mud4b wrote:HotFourOk wrote:Just soak it in petrol, then metho to dry it out
i hope your joking?
As joel said, Carby clean is fine. Or a carbon/throttle body cleaner. You shouldn't need to 'soak it' and it would probably be a good idea not to 'soak' the eletrics. All you need to do is clean the hot wire in the middle of the sensor. DONOT attempt to touch or wipe the hot wire. just spray.
The AFM will work for partial throttle applications, most Engine management systems have predetermined values for Wide Open Throttle (WOT) application and hardly rely on AFM response as economy is not an issue if your driving WOT so injector pulse and ignition timing will increase to predetermined values and things like AFM and O2 sensor become asthetic pretty much.
That explains why you may notice an improvement in throttle response from start off etc.
Cheers Dan
Hot40k is pulling the piss, he knows I have cleaned it already
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
What? I did that to mine after I used the sand for the port polishingmud4b wrote:HotFourOk wrote:Just soak it in petrol, then metho to dry it out
i hope your joking?
HnM finally feels like a big man again in his HiLux
[quote="RockyF70 - Coming out of the closet"]i'd be rushing out and buying an IFS rocky[/quote]
Who is online
Users browsing this forum: No registered users and 81 guests