Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Water temp gauge? where to install

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 1451
Joined: Sat Mar 18, 2006 1:25 pm
Location: hilux is in NSW.. Im in WA again

Water temp gauge? where to install

Post by brad 93hilux »

Has any one else with a 2.8d hilux installed a aftermarket water temp gauge?

Where did you put the sensor? (any pics)

I was thinking on removing my thermostat housing and next to the factory temp sensor there is another spot that looks like it could be drilled and tapped out to suit the fittings.

The only drama is the new probe has a 3/8 BSP fitting and i believe there might not be enough alloy left around the outside edge of the hole..

Any ideas on where i can plug the gauge onto?

Brad
3.0L turbo diesel, 4" lift, bud's front housing, track assasin cv's, air lokker front + Rear, beadlock'd 37 stickies, high steer, 15.5" travel ranchos, high pinion diff and coils on the rear
Top
Posts: 1451
Joined: Sat Mar 18, 2006 1:25 pm
Location: hilux is in NSW.. Im in WA again

Post by brad 93hilux »

some one must have installed one surely?????
3.0L turbo diesel, 4" lift, bud's front housing, track assasin cv's, air lokker front + Rear, beadlock'd 37 stickies, high steer, 15.5" travel ranchos, high pinion diff and coils on the rear
Top
Posts: 502
Joined: Wed May 02, 2007 3:29 pm
Location: Brackenridge...Boondall at heart

Post by Rory »

buy one of the alloy mounting tube/blocks that have the hole drilled and tapped in them. they go inline on ur upper rad hose, just cut the hose and clamp the tube inbetween the two ends. got one yesterday was $30ish at autobarn.
Boondall backyard performance...SHANTYTECH 4034...
BMX bike - 20" maxxis stickies, 4130 tube frame, reduction gears.
Top
Posts: 1451
Joined: Sat Mar 18, 2006 1:25 pm
Location: hilux is in NSW.. Im in WA again

Post by brad 93hilux »

do you have a photo of it?

Ill have to go down in the next couple of days and have a look.

Brad
3.0L turbo diesel, 4" lift, bud's front housing, track assasin cv's, air lokker front + Rear, beadlock'd 37 stickies, high steer, 15.5" travel ranchos, high pinion diff and coils on the rear
Top
Posts: 1254
Joined: Mon May 16, 2005 8:21 pm
Location: Sth Brissy

Contact:
Contact LuxyBoy

Post by LuxyBoy »

Rory wrote:buy one of the alloy mounting tube/blocks that have the hole drilled and tapped in them. they go inline on ur upper rad hose, just cut the hose and clamp the tube inbetween the two ends. got one yesterday was $30ish at autobarn.
I was also thinking of doing this; if no one replied with a better option.
Are they decent quality :?:
What are they made from :?:
Kind Regards,
Brad
Top
Posts: 502
Joined: Wed May 02, 2007 3:29 pm
Location: Brackenridge...Boondall at heart

Post by Rory »

i dont have a pic atm ill try and remembet to take one, its alloy and seems to be decent, didnt strip that tread out of the hole when i put the fitting in or when i screwed the earth onto it.
Boondall backyard performance...SHANTYTECH 4034...
BMX bike - 20" maxxis stickies, 4130 tube frame, reduction gears.
Top
Posts: 71
Joined: Fri Jun 01, 2007 5:41 pm
Location: crazy house

Post by robsrunner2 »

like this one but autobarn will have em
http://cgi.ebay.com.au/ws/eBayISAPI.dll ... :IT&ih=002
Top
Posts: 1451
Joined: Sat Mar 18, 2006 1:25 pm
Location: hilux is in NSW.. Im in WA again

Post by brad 93hilux »

Yeh i think i might get a piece of stainless pipe, drill a hole in the side and tig a stainless 3/8 BSP socket onto the side of it...

That would be easier than drilling and tapping my thermostat housing...

Cheers Brad
3.0L turbo diesel, 4" lift, bud's front housing, track assasin cv's, air lokker front + Rear, beadlock'd 37 stickies, high steer, 15.5" travel ranchos, high pinion diff and coils on the rear
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 15 guests