Has anyone put an m15a into a sierra? I'm looking at one which is very cheap but want to know if anyone has done the conversion?
Problems I would have etc...
Going into a 96 coily...
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
M15A into Sierra?
Gearbox choice is the problem.
The M motor has its own bolt pattern so the only gearboxes that fit straight up are from a Jimny. The Jimny manual doesn't suit a sierra well as it has a long extension housing for the shifter that will put the shifter pretty much all over the low range shifter.
The other option is the Jimny auto. Not a bad box, but cripplingly expensive to fix if you broke it.
Steve.
The M motor has its own bolt pattern so the only gearboxes that fit straight up are from a Jimny. The Jimny manual doesn't suit a sierra well as it has a long extension housing for the shifter that will put the shifter pretty much all over the low range shifter.
The other option is the Jimny auto. Not a bad box, but cripplingly expensive to fix if you broke it.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
apparently these will bolt straight into a jimny with a m13a engine, everything needs changing over from the m13a to m15a and apparently the ecu's are the same also (i cant see this being the case though.
i was going to do this to mine but looking into it further the throttle body of the m15a sits very far to the lhs of the swift and would hit the firewall on a sierra or jimny. other than that was the vvt-i, if you had a normal m13a and not the vvt-i it would need controlling i figure unless it runs off oil pressure like v-tec.
cheers mark
i was going to do this to mine but looking into it further the throttle body of the m15a sits very far to the lhs of the swift and would hit the firewall on a sierra or jimny. other than that was the vvt-i, if you had a normal m13a and not the vvt-i it would need controlling i figure unless it runs off oil pressure like v-tec.
cheers mark
Mud4b/ OPT, Cheap rates, Not cheap work. Search Opt- option offroad on facebook. Call or Sms 0439609525.. Sunshine coast, Eudlo, 4554.
Thanks for the advice, I couldnt find anything on here about it and wanted to know how/easy hard it would be.
So theres no chance the motor will bolt up to my sierra box?
Does this mean, if I did couple the motor with a jimny box that I would have to modify the shaft from the gearbox to the transfer case?
I can get the engine from an 07 swift for $450 and at that price I really dont want to pass it up.
So theres no chance the motor will bolt up to my sierra box?
Does this mean, if I did couple the motor with a jimny box that I would have to modify the shaft from the gearbox to the transfer case?
I can get the engine from an 07 swift for $450 and at that price I really dont want to pass it up.
a) No, the engine will not bolt up to your Sierra gearbox. Never.
B)The jackshaft (the shaft between the gearbox and the transfer)is the easy bit. If you want a manual, it's going to be a big PITA to make the shifter work with the transfer. If you want an auto, be prepared to have $$$ in the auto, wiring etc. (although it will fit)
Here's the problems I can think of:
Totally custom trans tunnel/shifters
Flywheel?
Maybe starter?
Clutch
Sump
Oil pickup
inlet manifold?
airbox
Fan
Radiator hoses
Radiator
Coolant lines (hard lines)
ECU if you have an auto donor motor or want a auto (which would be much easier to fit)
I know $450 sounds really good, but even if the motor was free I still think this will be an expensive and complex conversion. I've seen an M13 in a sierra and whilst it did fit OK, It was far from a drop in, and the guy building it had a whole auto jimny to pull parts from.
Not trying to be negative, but I really think the only way to viably build a M engined Sierra is to start with a Jimny wreck. There's too much weirdness with the M motor.
Steve.
B)The jackshaft (the shaft between the gearbox and the transfer)is the easy bit. If you want a manual, it's going to be a big PITA to make the shifter work with the transfer. If you want an auto, be prepared to have $$$ in the auto, wiring etc. (although it will fit)
Here's the problems I can think of:
Totally custom trans tunnel/shifters
Flywheel?
Maybe starter?
Clutch
Sump
Oil pickup
inlet manifold?
airbox
Fan
Radiator hoses
Radiator
Coolant lines (hard lines)
ECU if you have an auto donor motor or want a auto (which would be much easier to fit)
I know $450 sounds really good, but even if the motor was free I still think this will be an expensive and complex conversion. I've seen an M13 in a sierra and whilst it did fit OK, It was far from a drop in, and the guy building it had a whole auto jimny to pull parts from.
Not trying to be negative, but I really think the only way to viably build a M engined Sierra is to start with a Jimny wreck. There's too much weirdness with the M motor.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
The BB is a REALLY easy swap - I've done one.
GTI's are well past it IMHO and a poor candidate due to the dissy hassles. If you want a GTI you really want a G16B.
Steve.
GTI's are well past it IMHO and a poor candidate due to the dissy hassles. If you want a GTI you really want a G16B.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Posts: 912
Joined: Tue Nov 09, 2004 6:29 pm
Joined: Tue Nov 09, 2004 6:29 pm
Location: {Sydney, Australia or Rio, Brazil Ride: Sierra JXi}
How different is the m15 block to the m13 block proportianally?
Is it possible the m13 intake, exhaust and sump are bolt on (they often are in the g series)
Mark has already said the gearbix fits and the ecu are supposed to be interchagleble, even if he paid through the nose for an auto or did some tunnel mods for a manual it would be an intersting set up.
At $450 for the engine it might be an idea to go take a measuring tape to some one who has a jimny m13
Is it possible the m13 intake, exhaust and sump are bolt on (they often are in the g series)
Mark has already said the gearbix fits and the ecu are supposed to be interchagleble, even if he paid through the nose for an auto or did some tunnel mods for a manual it would be an intersting set up.
At $450 for the engine it might be an idea to go take a measuring tape to some one who has a jimny m13
-[b]Santos[/b][img]http://www.teamswift.net/images/smilies/icon_furious.gif[/img]
Suzuki, Jeep & Toyota Soft tops with welded seams for SALE (PM me)
Suzuki, Jeep & Toyota Soft tops with welded seams for SALE (PM me)
Just remember with the Jimny gearboxes, the earlier jimny's from 98 to 2001 that used the g13bb have the same gearbox bolt pattern etc as a 1.3 litre sierra From early 2001 Jimny's changed to a M13a engine and the gearbox to engine is different you will also find the headrest, is different, speedo goes to 180kmph from 160kmph Hazard switch, rear wiper switch and instrument writing font changed bla bla bla lots of tiny changes
Who is online
Users browsing this forum: No registered users and 6 guests