Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Harmonic balancer bolt,2H.

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 32
Joined: Mon Mar 31, 2008 12:17 pm
Location: COCKATOO

Harmonic balancer bolt,2H.

Post by vanners »

Can any one tell me the socket size required to undo the harmonic balancer bolt on the front of a 2H motor.Looks big.
Top
Posts: 189
Joined: Wed Sep 08, 2004 8:27 pm
Location: GYMPIE QLD

Re: Harmonic balancer bolt,2H.

Post by rock hopper »

vanners wrote:Can any one tell me the socket size required to undo the harmonic balancer bolt on the front of a 2H motor.Looks big.
it is a 45mm ...
L.C. AUTOMOTIVE PH:0754827077
4x4 PARTS + ACCESSORIES
TYRE WHEELS & RADIATORS - A/C
1 DuRIETZ COURT GYMPIE 4570
Top
Posts: 32
Joined: Mon Mar 31, 2008 12:17 pm
Location: COCKATOO

Post by vanners »

Cool,thanks for that.Any secret tricks to replacing seal?
Top
Posts: 189
Joined: Wed Sep 08, 2004 8:27 pm
Location: GYMPIE QLD

Post by rock hopper »

vanners wrote:Cool,thanks for that.Any secret tricks to replacing seal?
use a NOK brand seal ... (O.E.M PART)
use a speedy sleave if the ballancer is warn...
L.C. AUTOMOTIVE PH:0754827077
4x4 PARTS + ACCESSORIES
TYRE WHEELS & RADIATORS - A/C
1 DuRIETZ COURT GYMPIE 4570
Top
Posts: 32
Joined: Mon Mar 31, 2008 12:17 pm
Location: COCKATOO

Post by vanners »

I had a go at replacing the front crank seal today,however,i couldn't get the bolt undone.The issue was i couldn't stop the engine from turning(i think due to the fact that the old girl is LOW in compression)So without the convenience of a rattle gun,what is a good method?
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

vanners wrote:I had a go at replacing the front crank seal today,however,i couldn't get the bolt undone.The issue was i couldn't stop the engine from turning(i think due to the fact that the old girl is LOW in compression)So without the convenience of a rattle gun,what is a good method?
put it in gear

or if its applicable, wedge a bar and socket against something, ideally the chassis rail, and hit the starter

sounds dodgy, bit its actually widely used :)

MAKE CERTAIN THE ENGINE WILL NOT FIRE UP, HOLD EDIC IN FUEL SHUTOFF.
Top
Posts: 32
Joined: Mon Mar 31, 2008 12:17 pm
Location: COCKATOO

Post by vanners »

Sounds interesting!Theory seems logical!
Top
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

vanners wrote:Sounds interesting!Theory seems logical!
Works

Bazzle
Top
Posts: 32
Joined: Mon Mar 31, 2008 12:17 pm
Location: COCKATOO

Post by vanners »

Where do i get myself a 45mm socket?Checked tool shops,sizes go 43mm,46mm(no 45).Any ideas?
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 1 guest