Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

question on 60 series rear main seal?

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 58
Joined: Sun May 18, 2008 7:11 pm
Location: Adelaide

question on 60 series rear main seal?

Post by mrflibbles »

i have a 84 petrol 2f 60 series, cant see it dropping oil anywhere except for the rear of the motor after a long run!

my question is can i change the rear main in the car? without pulling the box/motor out? i just cannot be bothered pulling anything apart to far....
Posts: 1031
Joined: Sun May 01, 2005 10:22 pm
Location: Newcastle 2300

Post by joel HJ60 »

I can't see it being done without pulling the Box. I wouldn't worry about it until you have to maybe get the clutch done.
[b]1985 HJ60[/b]

[url]http://forum.ih8mud.com/60-series-wagons[/url]
Posts: 58
Joined: Sun May 18, 2008 7:11 pm
Location: Adelaide

Post by mrflibbles »

cheers that sounds great for a lazy bugger like me!
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

flywheel has to come off.
Posts: 810
Joined: Thu Jul 15, 2004 8:02 am
Location: Somewhere in NSW

Post by brighty »

joel HJ60 wrote:I can't see it being done without pulling the Box. I wouldn't worry about it until you have to maybe get the clutch done.
At the end of the day, if your cluch is still in good nick, you're prob better off ripping the box out and replacing the rear main seal otherwise by the time it gets that bad that it HAS to be replaced, chances are you will have to do the clutch as well due to all the oil being flicked around the insides of the bell housing and covering the clutch/pressure plates & flywheel.

Trust me I know :roll:

I've pulled the box out of my 2H cruiser quite a few times now... and up until the last time about 2yrs ago, I could have it on the garage floor within an hour of starting ....using one trolley jack, and that's without the use of air tools!!! ;)
When in doubt..... UTE-ERIZE it!!!
Posts: 58
Joined: Sun May 18, 2008 7:11 pm
Location: Adelaide

Post by mrflibbles »

i really have no idea how good the clutch is (seems to be fine at the moment), only just got the beast! i might just wait (for more $$) and do it all at once clutch and seal.
Posts: 675
Joined: Sat Dec 17, 2005 10:06 pm
Location: campbelltown

Post by Nat84 »

and i would also do the seal on the front of the box to as i made the mistake..

i put a new clutch in with machined flywheel and new rear main seal and after about a week that front seal on the box started to leak :bad-words:
Tires are like boobs, they always look big until you have played with them for a while, then you just want a bigger set
Posts: 89
Joined: Sun Dec 10, 2006 6:42 pm
Location: Sydney, NSW

Post by MYTANK »

I had mine leaking, wasn't replaced when clutch went.. clutch ended up lasting a whole 25,000 before it had to be replaced aswell.

It's a bit like stuffed if you do stuffed if you don't.. but if you have the $$ i'd just get the box out and replace the seal and clutch at the same time, if the clutch looks ok, then keep it.. but it's usually better to change it if you can afford it.

Dan
________
0/________\0
|O|------|O|
[]----o----[]
Post Reply

Who is online

Users browsing this forum: No registered users and 118 guests