Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Bolts in disimilar metals

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 30
Joined: Sat Mar 12, 2005 4:50 pm

Bolts in disimilar metals

Post by Pony »

Hi all;
I want to put a bolt into a cast alloy housing and am wondering what sort of bolt to use, as in high tensile steel, stainless, etc.
Just worried about any corrosion issues with disimilar metals.
On a different tangent, I want to put a bolt into cast iron, I think I will be fine with high tensile steel bolts with this?
thanks
Pony
Last edited by Pony on Sun Sep 07, 2008 8:52 pm, edited 1 time in total.
Top
Posts: 810
Joined: Tue Jul 08, 2008 8:40 pm
Location: vic

Post by ajsr »

use high tensile steel bolt and if in doubt use a small amount of copper anitseze grease, I use it on everthing its good shit
85 high roof 1.3, 6.5 tc, air lockers,ruf and 34 swampers. yep its an ugly pos.
Top
Posts: 74
Joined: Wed Sep 28, 2005 7:45 pm

Post by Thylacine »

ajsr wrote:use a small amount of copper anitseze grease, I use it on everthing its good shit
No good for stainless (galvanic reaction).
Best general anti-sieze is nickel-based.


ed
Top
Posts: 5803
Joined: Wed Feb 19, 2003 3:02 pm
Location: Brisbane

Post by ISUZUROVER »

If you are worried about corrosion between dissimilar metals, get a paste called "duralac" from a boating chandlery or similar. Just put some on the bolt/thread, then you won't have any problems.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
Top
Posts: 2590
Joined: Tue Jan 04, 2005 11:33 am
Location: Brisbane

Post by Chucky »

Thylacine wrote:
ajsr wrote:use a small amount of copper anitseze grease, I use it on everthing its good shit
No good for stainless (galvanic reaction).
Best general anti-sieze is nickel-based.


ed
X2. Nickel based is the way to go I reckon.
And dont used stainless nuts and bolts without putting this stuff on as the stainless an 'Gall" up and seize. even on the first tighten.

carefull with the creeping grease thou, if you get any on your finger and not realise it will get EVERYWHERE, You'll end up with it on your face, head, ears, nose, on your crank. you'd be amazed what parts of your body you touch through out the dayAnd it sucks to get off.
My Cruiser is Environmentally Friendly.

It runs on recycled Dinosaurs.
Top
Posts: 38
Joined: Sun Oct 28, 2007 9:52 pm
Location: Whyalla, SA

Post by harlequin »

isuzu rover is right duralac is used on all marine disimilar metals its unbeatable corrosion barrier the others are great on alike metals steel/copper /brass etc but ally is so low on the galvanic table just about everything will react with it i also think duralac is chromate conversion but not sure it is not good for your health so dont ingest it in any way
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 171 guests