Hello.
I need information about the torque specs for this engine, Nissan ZD30, TDI, wich I need this to repair this engine.
Any advice is appreciated.
Cheers!
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Nissan ZD30
The stuff is that the engine suffered lack of lubrication on the cylinders.
The piston rings came out from the block welded to the pistons, all 4 pistons and respective rings.
Connecting rod and main bearings are ok, crankshaft is standard.
The camshafts are ok too, just the usual stuff with cylinder head, valve replacements, valve seats, valve guides, valvle oil seals, the usual.
Cylinder head surface is good, a fine flat surface. The problem were with the pistons and rings.
This is a Patrol engine, the vehicle is a 2004 Patrol.
Thanks for the tip.
Cheers!
The piston rings came out from the block welded to the pistons, all 4 pistons and respective rings.
Connecting rod and main bearings are ok, crankshaft is standard.
The camshafts are ok too, just the usual stuff with cylinder head, valve replacements, valve seats, valve guides, valvle oil seals, the usual.
Cylinder head surface is good, a fine flat surface. The problem were with the pistons and rings.
This is a Patrol engine, the vehicle is a 2004 Patrol.
Thanks for the tip.
Cheers!
!Hola!
Is this the VVT engine? They have issues with high EGTs (exhaust gas temperature) melting the top end.
There is a thread in the tech section of www.aulro.com/afvb on them as well. A guy there installed a pre-turbo EGT on one, and the temps went to high 600's (oC) with almost no load.
Is this the VVT engine? They have issues with high EGTs (exhaust gas temperature) melting the top end.
There is a thread in the tech section of www.aulro.com/afvb on them as well. A guy there installed a pre-turbo EGT on one, and the temps went to high 600's (oC) with almost no load.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
personally i have one with nearly 200 000k's never had a drama.. got a mate who's put nearly 400 000 on one and its gettin pretty tired..
both have been serviced every 10000k's
hope this helps
both have been serviced every 10000k's
hope this helps
01 td42 GU patrol ute, with extra bits and pieces.
[quote="Bluefreak"][quote="ofr57"]flex is over rated :finger:[/quote]
You drive an IFS too, huh...???
:D[/quote]
[quote="Bluefreak"][quote="ofr57"]flex is over rated :finger:[/quote]
You drive an IFS too, huh...???
:D[/quote]
Me too!!Tomo_89 wrote:personally i have one with nearly 200 000k's never had a drama.. got a mate who's put nearly 400 000 on one and its gettin pretty tired..
both have been serviced every 10000k's
hope this helps
We've owned the 'family bus' GU since new (May 2001), its got 170k on it and has never missed a beat, but it has been maintained as per schedule (10 000km intervals) with semi syn oil. But I must admit, I am thinking to changing it to 5000km intervals, with a good oil flush every time.
Big Dave, Scarborough, Qld
Loose Screws 4wd Racing Team
Loose Screws 4wd Racing Team
Who is online
Users browsing this forum: No registered users and 2 guests