G'day all,
after bending a lower control arm the other day we chucked in a set of heavy duty arms and panhards. Now the truck was driving fin before hand, but after it was all in I went for a drive and found that I had very low power at high revs, only just enough forward movement to change from 2nd to 3rd at 3-4 grand. The only thing I can think of is that the hand brake has jammed on (we were using this to hold the wheel still while rotating the diff to get the arms in).
Does this sound plausible?
I am a little concerned, but oil levels are fine, no new noises, just slug like power. Has this happened to anyone else? If so, what were your experiences and what did you do to overcome it.
Cheers,
GFN
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
High revs Low power
High revs Low power
[quote="MissForbyNooB"] I've played with you AND your missus. [/quote]
Right,
So, I looked through all the possible problem areas in a systematic easy fix to hard fix fashion. The handbrake was not stuck on as the drum came off freely, but it was full of crud and not too far from jamming (I cleaned it all up). With the tail shaft off I jacked the rear axel up and tried turning the wheels by hand from the diff centre - this was quite hard, but do-able, so not the problem. I reconnected the driveline and turned the truck on, slipped it into gear and gave it some revs. The wheels didn't turn, I revved harder, they turned: Interesting. Taking out the axel stands I decided one last final test: Into gear, foot off clutch, foot off accelerator, foot on brake. It didn't stall. I had finally found the problem...my clutch is cactus.
It was parked around the corner from the local mechanics, so we towed it in. Looks likely to cost $1500 for a heavy duty clutch and labour. Annoys me a lot, but I don't have the space to do it myself and street repairs only stretch to the minor ares!
At least I now know it has a strong clutch that will last now. Before I finish writing I will let you in on the condition of the old clutch. I pooped down to the garage and had a look. The clutch still had a little life in it, but the bearings and the pressure plate were rusted to all hell. It had gotten to the point where the pressure plate was actually seized open - one of the previos owners has told a porky pie to one of the new owners...grrrr.
Cheers,
GFN
So, I looked through all the possible problem areas in a systematic easy fix to hard fix fashion. The handbrake was not stuck on as the drum came off freely, but it was full of crud and not too far from jamming (I cleaned it all up). With the tail shaft off I jacked the rear axel up and tried turning the wheels by hand from the diff centre - this was quite hard, but do-able, so not the problem. I reconnected the driveline and turned the truck on, slipped it into gear and gave it some revs. The wheels didn't turn, I revved harder, they turned: Interesting. Taking out the axel stands I decided one last final test: Into gear, foot off clutch, foot off accelerator, foot on brake. It didn't stall. I had finally found the problem...my clutch is cactus.
It was parked around the corner from the local mechanics, so we towed it in. Looks likely to cost $1500 for a heavy duty clutch and labour. Annoys me a lot, but I don't have the space to do it myself and street repairs only stretch to the minor ares!
At least I now know it has a strong clutch that will last now. Before I finish writing I will let you in on the condition of the old clutch. I pooped down to the garage and had a look. The clutch still had a little life in it, but the bearings and the pressure plate were rusted to all hell. It had gotten to the point where the pressure plate was actually seized open - one of the previos owners has told a porky pie to one of the new owners...grrrr.
Cheers,
GFN
[quote="MissForbyNooB"] I've played with you AND your missus. [/quote]
Who is online
Users browsing this forum: No registered users and 118 guests