Hi all im looking for a snokle to fit my p38 has anyone come across one ?
also has anyone made one for their rangie if you have can you place some pic for me to look at
cheers
Brendon
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
p38 snorkle
Moderator: Micka
p38 snorkle
Cheers
Brendon
2008 nissan patrol
Factory bullbar with 12000lbs ironman winch, PLESSEY_MTR96_UHF 100ch 25watts
needs diff lock F/R
Brendon
2008 nissan patrol
Factory bullbar with 12000lbs ironman winch, PLESSEY_MTR96_UHF 100ch 25watts
needs diff lock F/R
Here is one we did in my old shop...sorry for the link but I dont have any of the original pics on my laptop......http://www.landroversonly.com/forums/f3 ... ndex1.html
Last edited by rovermech on Tue Nov 18, 2008 9:56 am, edited 1 time in total.
P38 Snorkel
Gu Patrol grafted to P38. Looks GR8. Some plumbing was required under guard!!!
P38 snorkel
Take Two....
http://picasaweb.google.com.au/dck7aok/P38Snorkel#
http://picasaweb.google.com.au/dck7aok/P38Snorkel#
p38 snorkel
Firstly, Rangie96 owns this vehicle(he is online).
Unfortunately we overlooked the need to take photos during the install process. Alas job was pretty much easy.
This particular Safari snorkel has an offset to clear the very rounded top of a Gu patrol guard.
Original plumbing is thrown away. rear section of snorkel was patched up and new 2&1/2 inch flange(aluminium pipe) fitted to lowest possible position with rivets and lots of sika. fitted template to snorkel and remarked new penetration and mounting bolts, transfered to guard, Holes drilled.
We used silicone turbo hose elbows(two off). A straight peice of tube runs under the guard(above the plastic inner guard - which requires heat modifications) and into the airbox...
Snorkel is not solidly mounted to guard, instead we used rubber grommets in the holes with large washers behind. This allows a little more tip to clear the bonnet on opening(just closes the visible gap at top of bonnet when bonnet is down). And can be tighted or loosen to adjust.
I will endevour to get some photos up soooooooon.......
cheers for compliments.
Unfortunately we overlooked the need to take photos during the install process. Alas job was pretty much easy.
This particular Safari snorkel has an offset to clear the very rounded top of a Gu patrol guard.
Original plumbing is thrown away. rear section of snorkel was patched up and new 2&1/2 inch flange(aluminium pipe) fitted to lowest possible position with rivets and lots of sika. fitted template to snorkel and remarked new penetration and mounting bolts, transfered to guard, Holes drilled.
We used silicone turbo hose elbows(two off). A straight peice of tube runs under the guard(above the plastic inner guard - which requires heat modifications) and into the airbox...
Snorkel is not solidly mounted to guard, instead we used rubber grommets in the holes with large washers behind. This allows a little more tip to clear the bonnet on opening(just closes the visible gap at top of bonnet when bonnet is down). And can be tighted or loosen to adjust.
I will endevour to get some photos up soooooooon.......
cheers for compliments.
Who is online
Users browsing this forum: No registered users and 2 guests