Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

trouble with engine stopping for split second

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 14
Joined: Tue Jun 06, 2006 7:30 pm
Location: brisbane

trouble with engine stopping for split second

Post by whiteghost60 »

i have 1989 hj60 2h cruiser that will stop just for a split second
it has a fully reconditioned injector pump only 12 months old and new injectors new fuel filter.
can any body tell me whether it might be a electrical problem with the shut off solenoid and how do i test it or is there any other problem that some one has come across.
the engine does not totally stop. :?
Top
Posts: 2601
Joined: Tue Jul 13, 2004 8:02 pm
Location: warner, brisbane

Post by chunderlicious »

i got told it as the governor diaphragm being worn out. only happens when you let off the accelerator? or othet times?
turbos are nice but i'd rather be blown
Top
Posts: 5
Joined: Sat Nov 10, 2007 8:11 pm
Location: rochester

Post by p_dids_22 »

i had a similar problem with my 75s 2h motor.... cheack you alternator regulator mine was changing volage and with the lights on it woud do it and with the heater on also
Top
Posts: 310
Joined: Fri May 25, 2007 12:16 am
Location: at the shed gympie

Post by scuba steve 22 »

had the same problem awhile back when using lights or air con
pretty sure i replaced the control box behind the kick panel
hope it helps
steve
Top
Posts: 93
Joined: Sun Oct 22, 2006 10:33 pm
Location: Sunshine Coast

Post by GT60 »

I had the same problem with my 2h, turned out to be a loose connection on oil pressure sender giving a false no oil pressure signal and shutting down for a split second...
Top
Posts: 1090
Joined: Mon Jun 02, 2003 6:58 pm
Location: Hobart

Contact:
Contact DR Frankenstine

2h

Post by DR Frankenstine »

Mine did the same thing, turned out to be the connector plug to the edic control motor
Remember some days your the pigeon and other days your the statue
Top
Posts: 13
Joined: Fri Nov 28, 2008 6:03 pm
Location: mildura

Post by rad... »

My bj73 did the same thing only while the lights where on, turned out that i needed a cable connecting the earth on the battery to the body and that has fixed it. hope that helps. ;)
Top
Posts: 357
Joined: Fri Nov 07, 2003 3:30 am
Location: Mount Beauty

Post by Trusa »

The above two responses are your most likely causes. If it becomes more frequent/rapid with more accessories turned on then it is most likely a loose earth causing your Edic motor to cycle.

You can visually check this by running engine and turning lights on and watching the connector rod between the edic motor and injector pump cycle through in unison with the motor dying and returning to idle.

Check battery earth and edic motor plugs. Bad battery earth was my experience also.

Ben
Top
Posts: 6021
Joined: Sat Feb 15, 2003 11:01 pm
Location: Shed.

Post by dumbdunce »

x3 on poor earth to the EDIC, it causes the motor to creep very slowly until it cycles.
Free air locker to the first 20 callers!
Top
Posts: 270
Joined: Tue Jul 08, 2008 4:47 pm
Location: Burpengary.... Where the hell is that?

Post by Red Dog 4x4 »

My bj73 did the same thing only while the lights where on, turned out that i needed a cable connecting the earth on the battery to the body and that has fixed it. hope that helps.
That what me 60 did and it fixed the prob....
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 11 guests