Can you get an airlocker to suit 40 spline axles with a 9" centre.
I believe the carrier bearings are diferent to the 35 spline - so not sure its as simple as side gears.
I would like it instead of the spool as I can use it on the street, without the hassle / disadvantage of removing an axle.
thanks
Bru
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
ARB locker for 9" 40 spline
Moderators: toaddog, TWISTY, V8Patrol, Moderators
ARB locker for 9" 40 spline
ADHD Racing would like to thank
Mrs Bru @ Sunshine Coast Developmental Physiotherapy - www.scdphysio.com.au , Ryano @ Fourbys www.generaltire.com.au Blitzkrieg Motorsport
Mrs Bru @ Sunshine Coast Developmental Physiotherapy - www.scdphysio.com.au , Ryano @ Fourbys www.generaltire.com.au Blitzkrieg Motorsport
not to my knowledge. According to Daniel from ARB's posts on pirate they are currently tooling up to do 40 spline, but I would think it would be for the 14 bolt diffs, not the 9 inches.
There is also known weaknesses with the use of an ARB in a 9 inch - plenty of info re this on pirate.
For my KOH buggy we have pulled the front spool out and put a 35 spline ARB in for the Vegas to Reno race. I am not convinced I will run the ARB in KOH, I may put the spool back in. The rear is 40 spool.
Have you actually purchased your rear housing yet? What about looking at the new custom 14 bolt housings, like what Dave Cole is using in his new racer. I will be interested to see how it performs next week.
Ben
There is also known weaknesses with the use of an ARB in a 9 inch - plenty of info re this on pirate.
For my KOH buggy we have pulled the front spool out and put a 35 spline ARB in for the Vegas to Reno race. I am not convinced I will run the ARB in KOH, I may put the spool back in. The rear is 40 spool.
Have you actually purchased your rear housing yet? What about looking at the new custom 14 bolt housings, like what Dave Cole is using in his new racer. I will be interested to see how it performs next week.
Ben
AFAIK NO, but you can surely get the 31 or 35-spline EDM'd to 40-spline.
e.g. Jacmac does rover ARBs side gears for a couple of hundred $$$
Alternately email daniel bongard on here and see if there is anything under development.
This seems to be what is available:
e.g. Jacmac does rover ARBs side gears for a couple of hundred $$$
Alternately email daniel bongard on here and see if there is anything under development.
This seems to be what is available:
Ford 9-inch Axle - Nine-Inch, Nailed Part I
Here's a cross section of available differentials. Clockwise from 12 o'clock: Detroit Locker, ARB Air Locker, 40-spline spool, mini-spool, Trophy Truck spool, stock open differential, Detroit Truetrac, and Ford Trac-Lok. The mini-spool installs into a stock open differential and replaces the side gears. To run the Trophy Truck spool, you'll also need a Trophy Truck-size axlehousing, axleshafts, gearcase, and T.T.-size full-floating hubs. The beauty of the 9-inch is that it can be used in a wide spectrum of vehicles on an equally wide spectrum of budgets.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
Who is online
Users browsing this forum: No registered users and 3 guests