Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Engine light flashing and rodeo wont start???

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 109
Joined: Wed Mar 14, 2007 4:24 pm
Location: Brisbane, Qld

Engine light flashing and rodeo wont start???

Post by peeko22 »

i went to start the rodeo (3.5L v6 140 000k) this morning and it just kept ticking ovetr and woulndnt start.

the engine light was flashing and the manual says nothin.
i am on a slight hill but nothin major , i rollded back so its level about a metre and turned it over again and its all sweet started perfect engine light stopped flashing .

why would this do this is it electrical or is the fuel pump or somethin on its way out . it has done this a few times and have no idea
Email - flossamarosus@hotmail.com
Posts: 24
Joined: Mon Jun 22, 2009 7:09 pm
Location: Langwarrin

Post by Chops_69 »

Its your key mate the head is faulting and the body control module aint seeing the key u may need a new key
Give a man fish and feed him for a day.

Teach a man to fish and he will sit in a boat and drink beer all day.
Posts: 109
Joined: Wed Mar 14, 2007 4:24 pm
Location: Brisbane, Qld

Post by peeko22 »

can i just get one cut or do i have to go to holden???
Email - flossamarosus@hotmail.com
Posts: 109
Joined: Wed Mar 14, 2007 4:24 pm
Location: Brisbane, Qld

Post by peeko22 »

can i just get one cut or do i have to go to holden???
Email - flossamarosus@hotmail.com
Posts: 5714
Joined: Fri Nov 22, 2002 3:55 pm
Location: Perth WA.

Post by nicbeer »

Holden, and prepare for a#$ r#$#ing if they are like some other car makers
[url=http://www.outerlimits4x4.com/viewtopic.php?p=930942#930942&highlight=]Zook[/url]
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
Posts: 68
Joined: Tue Mar 11, 2008 10:41 pm
Location: Brisvegas

Post by SilverBulletBM »

It could be the immobilizer or the earth points for the immobilizer. Not an uncommon fault. Check all the earth points in the engine bay (all the wires from the harness that mount to the body), remove the bolts, make sure that they're making good contact with a metal surface and not paint. Then theres a point in the cab, under the passenger seat under the floor carpet/vynal, there's a point there that needs to be cleaned and the terminal soldered to the wiring harness.
Posts: 109
Joined: Wed Mar 14, 2007 4:24 pm
Location: Brisbane, Qld

Post by peeko22 »

cheers guys i'll give it a shot and see how it goes
Email - flossamarosus@hotmail.com
Posts: 381
Joined: Sun Jan 23, 2005 2:56 pm
Location: singleton

Re: Engine light flashing and rodeo wont start???

Post by nayto »

peeko22 wrote:i went to start the rodeo (3.5L v6 140 000k) this morning and it just kept ticking ovetr and woulndnt start.

the engine light was flashing and the manual says nothin.
i am on a slight hill but nothin major , i rollded back so its level about a metre and turned it over again and its all sweet started perfect engine light stopped flashing .

why would this do this is it electrical or is the fuel pump or somethin on its way out . it has done this a few times and have no idea
Hows your engine oil level, iv seen this before, they can chew through a bit of oil and rodeos wont start if its low, that could be your fault light and why it started when you were on level ground.
Posts: 381
Joined: Sun Jan 23, 2005 2:56 pm
Location: singleton

Post by nayto »

so how'd u go peeko? get it sorted
Subversive Bucolicism
Posts: 9196
Joined: Sat Mar 13, 2004 10:47 pm
Location: I think I hear a Dingo eating your Baby

Post by longlux »

We had this same problem with one of our work vehicles, the only way could get it to start was uncouple the cables from the computer then plug then back in.


I think they eventually replaced the computer.
Workplace Safety :
Destroying our forests one Take 5 at a time.

Every time you do a Take 5 an Orangutan cries.

https://www.facebook.com/shadowthetravelcat" onclick="window.open(this.href);return false;
Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests