hi all... my first post here so i'll do a quick intro first: i'm from south east melbourne and i drive an 89 feroza (not feroza II unfortunately) which the previous owner moded up a bit (extractors, new exhaust, snorkel).
i've read around the place that removing the sway bar seems to be a common mod to do. i don't know much about this sort of thing at the moment but i'm keen to learn. what does the sway bar do? what difference does removing it make to onroad/offroad handling? is it difficult to remove??
thanks!!
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
sway bar...
Moderator: Tiny
Sway bar ...........
The sway bar does what it sounds , it stops the car from swaying around when cornering etc and the idea of removing the sway bar is to give a little more wheel travel , 4 bolts and it's off ........
Andy...........
All post's are submitted with the assistance of alcohol
"OUR FEROZA" is Debt Propelled
All post's are submitted with the assistance of alcohol
"OUR FEROZA" is Debt Propelled
Hi and Welcome!
The Anti-Sway bar is installed in the front with the independant front suspension. It's job is to stop body roll basically. But as a result it limits how much the wheel can go up and down (articulation) offroad.
It's a fairly thin round bar that connects from the bottom arm of one front wheel to the other. It is connected in 4 points. One at each wheel and 2 under your front bash plate. It's sort of U shaped, pointing towards the front of the car..you can't miss it really..
Fairly easy to remove. Best thing is spray where it's bolted to the car with some wd40 a few days before removing it to help loosen the bolts. Remove your bash plate and undo the two bolts there, take the rubber off as well. Now do it where it joins the lower control arms on the inside of each front wheel, these were the hardest for me to take off but will do so with a bit of grunting
Onroad difference...if your car is lifted, you won't notice much difference. If it's not you may notice more roll when going around corners, but you adjust to it after a few days...I've forgotten I've taken mine off to be honest.
Offroad, you get a few more inches of travel, which always helps.
The Anti-Sway bar is installed in the front with the independant front suspension. It's job is to stop body roll basically. But as a result it limits how much the wheel can go up and down (articulation) offroad.
It's a fairly thin round bar that connects from the bottom arm of one front wheel to the other. It is connected in 4 points. One at each wheel and 2 under your front bash plate. It's sort of U shaped, pointing towards the front of the car..you can't miss it really..
Fairly easy to remove. Best thing is spray where it's bolted to the car with some wd40 a few days before removing it to help loosen the bolts. Remove your bash plate and undo the two bolts there, take the rubber off as well. Now do it where it joins the lower control arms on the inside of each front wheel, these were the hardest for me to take off but will do so with a bit of grunting
Onroad difference...if your car is lifted, you won't notice much difference. If it's not you may notice more roll when going around corners, but you adjust to it after a few days...I've forgotten I've taken mine off to be honest.
Offroad, you get a few more inches of travel, which always helps.
Who is online
Users browsing this forum: No registered users and 1 guest