Is there anyways known to god of getting the pitman arm of of a non power steer box of an MQ Patrol??
In the end i had to rebuild a steering box i had lying around that was seized cause i couldnt get the pitman arm of the one on my rig so i could swap it for a different one.
At Chaos they used a 2 tonne jack in a pipe bender. Is there an easier way??
Screwy
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
PITMAN ARM!!!
PITMAN ARM!!!
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
heat and a puller
Find a strong puller and attach it and tension it as much as you can before anything brakes. Then shock-heat the pitman arm witha torch, but be careful not to heat too much. The key is to heat it so fast the shaft inside doesn't heat up along with it. That way the hole in the pitman arm should increase a tiny little bit, enough to pull the arm off. And it that isn't enough, slam your largest hammer on top of the puller screw and tension between each blow.
I once yused this approach on a brake drum sittion on a konical axle, the parts flew 2 metres off when it finally loosened, (so stay out of harms way!), but it came off!
totto
God of Magnificant Ideas!
I drank more beer and swore a bit, but finally remembered that some champ showed me how to use the Oxi thats here, ( I was only using a blow torch). I heated it and quenched it and then took the quarter panel off and used a hammer longer than my arm that must way at least 20kgs and belted the Living hell out of it 
( and yeah i remembered the cold water trick when i remember the oxi lesson, thanks ). 
It came off...... and so did the shoe i was wearing real quick. God it hurts when u hit ur foot with a hammer......
Screwy
( and yeah i remembered the cold water trick when i remember the oxi lesson, thanks ).
It came off...... and so did the shoe i was wearing real quick. God it hurts when u hit ur foot with a hammer......
Screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
God of Magnificant Ideas!
V8Patrol wrote:fit up a puller.....
heat up with oxy....
quench with cold water....
and belt d fug out of it with a big hammer !!!
remember the cold water trick i showed you on ya towball nut ????
The word FOOT is not included in my post ..... just double checking
did ya break anything ?????????
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
You may have to press it off on a hydraulic press.
The pitman arm is usually splined but can lock up with age requiring some serious pressure to separate the arm from the rod.
Idler arms are usually a taper fit and can be a real bitch to separate from the bell crank rod.
The pitman arm is usually splined but can lock up with age requiring some serious pressure to separate the arm from the rod.
Idler arms are usually a taper fit and can be a real bitch to separate from the bell crank rod.
I just luv my "clacker Jabber"
Who is online
Users browsing this forum: No registered users and 4 guests