Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

hd-ft max fuel adj

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 24
Joined: Tue Nov 28, 2006 11:31 am
Location: Perth wa

hd-ft max fuel adj

Post by mozza »

Gday all, have fitted saf i/c kit .spaced the wategate and now looking at adj max fuel ,I am assuming it is the spoke socket long adj screw straight out the back but cant confirm in any manual, so im calling on the vast knowledge of the outerlimits toyota crew to guide my hand ....any help much appreciated ...

Cheers all Mozza
Posts: 337
Joined: Wed May 21, 2008 3:47 pm
Location: Birkett Place sth geelong

Post by Auto-Craft »

Thats normally the last adjustment, after doing timing, plunger, and off boost fuelling, then adjust the fuel, which also adds to the others.

lcool.org there is a good tech document on how to do your pump adjustemnts, and how to set them.

HAve you chnaged exhaust ?

Have a pyro fitted to adjust/tune it ?
Supercharged 80 SOLD - "OPERATION SANDY" now in effect.
Posts: 24
Joined: Tue Nov 28, 2006 11:31 am
Location: Perth wa

Post by mozza »

GDay Mate , yes has 3" system and pyro pre turbo and all LCOOL adj c/out , running heaps cooler than previously and final adj ready to c/out , i believe 1/16 increments are the go and am assuming that the screw i mentioned is the correct one?
Cheers for the reply mate ...
Posts: 337
Joined: Wed May 21, 2008 3:47 pm
Location: Birkett Place sth geelong

Post by Auto-Craft »

If you have done all the other mods and exhaust, start with 1 full turn, should be pretty close, if its not been touched before.

go in 1/2 turn increments.
Supercharged 80 SOLD - "OPERATION SANDY" now in effect.
Posts: 24
Joined: Tue Nov 28, 2006 11:31 am
Location: Perth wa

Post by mozza »

Gday again ,have cranked up to 2/3 of a turn after trying 1/2 turn , loving the change and temps are not up to pre install levels as yet and the engine dosent work any where near as hard as before ,in regards to boost pressures when c/control engagued only small increment s on long hills to maintain speed .All in all very happy with results so far , should have done it years ago!!!!
Posts: 619
Joined: Thu Nov 03, 2005 11:20 am
Location: vic

Re: hd-ft max fuel adj

Post by Hamo »

mozza wrote:Gday all, have fitted saf i/c kit .spaced the wategate and now looking at adj max fuel ,I am assuming it is the spoke socket long adj screw straight out the back but cant confirm in any manual, so im calling on the vast knowledge of the outerlimits toyota crew to guide my hand ....any help much appreciated ...

Cheers all Mozza
Where did you buy the safari kit from and if you dont mind how much $$
PM if you like I'm doing the same soon very soon
[quote="RN"]So do you support your local vendor...not if it is going to cost me almost double. [quote]
Posts: 24
Joined: Tue Nov 28, 2006 11:31 am
Location: Perth wa

Post by mozza »

Gday Hammo, Motsons 4x4 in brisbane will suppy kit for @ 2 g's or Armadale 4x4 in Perth for the same , most places who stock will not supply only but will fit /supply for @ 3200 ,hit up your local supplier and tell them you can get it from either them or Motsons and they might come to the party ,that is what I did with Armadale over here .


Enjoy Mozza.
Posts: 619
Joined: Thu Nov 03, 2005 11:20 am
Location: vic

Post by Hamo »

mozza wrote:Gday Hammo, Motsons 4x4 in brisbane will suppy kit for @ 2 g's or Armadale 4x4 in Perth for the same , most places who stock will not supply only but will fit /supply for @ 3200 ,hit up your local supplier and tell them you can get it from either them or Motsons and they might come to the party ,that is what I did with Armadale over here .


Enjoy Mozza.
Thanks mozza Yep i've heard of the supply & fit bit but be damed if i'm going to pay some one to fit it when i can do it my self
[quote="RN"]So do you support your local vendor...not if it is going to cost me almost double. [quote]
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests