Been out of the game for a bit while working on the house. Any way the itch has returned and I am working through some bits and pieces.
On to the topic at hand - I am confused - Reading through the diff swap banter I am wondering why MQ diffs get a mention, but no mention of GQ?
Are the GQ's not a better choice since they have rear disc brakes standard?
Simon
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
GQ versus MQ Diff Swap
Thanks I recognise the need for custom mounting.
I had assumed (likely incorrectly) that a double card driveshaft would take care of the lack of offset - I assume this is wrong? What is the answer in the all the Hilux conversions that occur.
Being too big - are you generalising that both the MQ and GQ are too big for Sierras?
Simon
I had assumed (likely incorrectly) that a double card driveshaft would take care of the lack of offset - I assume this is wrong? What is the answer in the all the Hilux conversions that occur.
Being too big - are you generalising that both the MQ and GQ are too big for Sierras?
Simon
A double cardan driveshaft is actually worse at correcting an offset diff than a normal uni. Double cardan joints are designed to bear all the angle, with the uni at the other end bearing as little angle as possible.
MK/MQ's bolt up to WT front. The front MQ centre is quite small. THe rear is big, for sure, but can be shaved pretty heavily.
They are also narrower than GQ, so they are a better fit if you want to build something legal/legalish.
Steve.
MK/MQ's bolt up to WT front. The front MQ centre is quite small. THe rear is big, for sure, but can be shaved pretty heavily.
They are also narrower than GQ, so they are a better fit if you want to build something legal/legalish.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
simobimo wrote:Steve - your double cardan comment has confused me. I don't fully understand why the situation is made worse.
I thought that people who put hilux diffs in use a double cardan to reduce vibration? Is that not the case?
Simon
Double Cardinals have a very small range of operation before they bind. My Fathers Hilux had to have the factory double-Cardinal removed because its rather unflexy front suspension was still causing bind up issues.
Wheeling on completely wicked angles, without even looking stable.
Double cardan joints are a form of constant velocity joint. That's because they contain 2 unis and the velocity variations of each one cancel the other out.
That means that if the uni at the other end of the driveshaft is at an angle, the driveshaft will vibrate as the uni cycles though it's velocity variations.
The DC joints in patrols/hiluxes etc aren't there to allow for big angles, as highway star says - they often allow very little angle at all. They are there to allow mismatched angles when the transfer is tilted down at the back to make the rear angles equal - that makes the front driveshaft unequal so the front diff is rotated to point straight at the transfer and a DC is employed to take al the angle.
with an offset rear driveshaft, it's not possible to have all the angle borne on one end of the driveshaft so you'll get vibration with a DC. You might not with a normal uni at each end.
Steve.
That means that if the uni at the other end of the driveshaft is at an angle, the driveshaft will vibrate as the uni cycles though it's velocity variations.
The DC joints in patrols/hiluxes etc aren't there to allow for big angles, as highway star says - they often allow very little angle at all. They are there to allow mismatched angles when the transfer is tilted down at the back to make the rear angles equal - that makes the front driveshaft unequal so the front diff is rotated to point straight at the transfer and a DC is employed to take al the angle.
with an offset rear driveshaft, it's not possible to have all the angle borne on one end of the driveshaft so you'll get vibration with a DC. You might not with a normal uni at each end.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
i vote for GQ diffs...
the easy option isn't always the best option.
just because the MQ come close to bolting in - that's not enough reason to pick them. just pull the body off the car and move put a different transfer in there to sort out the diff offset issue.
really - how hard could it
the easy option isn't always the best option.
just because the MQ come close to bolting in - that's not enough reason to pick them. just pull the body off the car and move put a different transfer in there to sort out the diff offset issue.
really - how hard could it
DMA Founding Member #1 - Now Retired
Or you could buy mine on 60 series diffs already done and engineered. (Shamless plug)
MQ is a relatively easy conversion on a Wide Track. GQ's would be a bit of work.
What are you hoping to achieve? strength? width? ratio? budget?
MQ is a relatively easy conversion on a Wide Track. GQ's would be a bit of work.
What are you hoping to achieve? strength? width? ratio? budget?
[quote="Harb"]Well I'm guessing that they didn't think everyone would carry on like a big bunch of sooky girls over it like they have........[/quote]
Who is online
Users browsing this forum: No registered users and 44 guests