ive got a auto gq patrol.
i want a 2inch body lift in it, running 4/5inch coils.
i been told you run into trouble with either the gearstick or the transfer stick.
please tell me ur personal experience and what i have to do fix this.
cheers!
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
bodylift on a auto gq patrol issues ?
this question has been asked before and i said what i had to do gq 89 auto wagon cut a bit out behind the low range shifter because i couldnt get low range then just adjust your steering shaft. but had arguments about that and bending the shifter and modding the actuator length i like my way was easy and just used a drill hammer and chisel.
Blown ls1 GQ winch truck. and GU tow car / daily
Cutting the floorpan is one way but this is the way we do it.
All we do is cut in front of the shifter down low, cut about half way through the shifter(below the floorpan if possible) we usually use a thin disc and do about 3 cuts next to each other so their is about 4mm total material removed.
Bend the gearstick forwards( this is why you dont cut right through. test drive the vehicle , if all good then run a weld over the cuts , it looks very neat from above and below .
Every one does things different , its your choice how neat you want your truck.
This way also means you do not damage the seal between your floorpan and your shifter boot.
All we do is cut in front of the shifter down low, cut about half way through the shifter(below the floorpan if possible) we usually use a thin disc and do about 3 cuts next to each other so their is about 4mm total material removed.
Bend the gearstick forwards( this is why you dont cut right through. test drive the vehicle , if all good then run a weld over the cuts , it looks very neat from above and below .
Every one does things different , its your choice how neat you want your truck.
This way also means you do not damage the seal between your floorpan and your shifter boot.
+++++NOW ON FACEBOOK++++++
www.superiorengineering.com.au
Largest 4x4 online superstore
SPONSOR OF TOUGH TRACKS
DGR RACE TEAM
JOOMBIE RACING
AMADA XTREME RACE TEAM
MAYBELINE RACING
MMM RACING
www.superiorengineering.com.au
Largest 4x4 online superstore
SPONSOR OF TOUGH TRACKS
DGR RACE TEAM
JOOMBIE RACING
AMADA XTREME RACE TEAM
MAYBELINE RACING
MMM RACING
Re: bodylift on a auto gq patrol issues ?
I did it to my auto, then removed it..vitopatrol wrote:please tell me ur personal experience and what i have to do fix this.
cheers!
if your running a 5inch suspension lift, how much more do you need? You'll clear plenty big tyres with 5inch if you do it right.
Re: bodylift on a auto gq patrol issues ?
Agreed!!! Check superiours comp truckbogged wrote:I did it to my auto, then removed it..vitopatrol wrote:please tell me ur personal experience and what i have to do fix this.
cheers!
if your running a 5inch suspension lift, how much more do you need? You'll clear plenty big tyres with 5inch if you do it right.
Blown ls1 GQ winch truck. and GU tow car / daily
Who is online
Users browsing this forum: No registered users and 125 guests