Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

CQ chassis help!

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 45
Joined: Thu Jan 28, 2010 7:46 am
Location: Narre Warren

CQ chassis help!

Post by Dabbott »

Hey all,

I posted a wanted ad in the wanted section for a Gq roller chassis,
I have a bloke thats got one, just curious as i have seen somewhere that the 2.8 diesel chassis engine mount location may be different to the 4.2's????

Reason i ask is that i am getting a chassis to replace the leaf sprung chassis in my ute.
Just want to make sure i am not going to run into any problems!

Thanks
Top
Posts: 1857
Joined: Fri Feb 02, 2007 12:16 am
Location: ipswich

Post by nastytroll »

Move the mount before fitting the rest of the vehicle to it. Just measure it off the other one.
Top
Posts: 45
Joined: Thu Jan 28, 2010 7:46 am
Location: Narre Warren

Post by Dabbott »

I am unsure if it is a 2.8 chassis. i was just asking the question.
If worst comes to worst i will,

But its just a long way to go to get it, and a lot of $$$ to find out its wrong!
Top
Posts: 1857
Joined: Fri Feb 02, 2007 12:16 am
Location: ipswich

Post by nastytroll »

I have a swb that has had a chassis replaced by creative conversions. It has had the LHS engine mount moved and wheel base shortened. I'm assuming it was a 2.8 chassis. The previous owner said the original chassis broke the upper trail arm cross member out and a swb chassis was not available to replace it.

Its not a big job to move the engine mount, but a good condition chassis can be hard to find at times.
Top
Posts: 237
Joined: Sun Dec 06, 2009 2:03 pm
Location: QLD

Post by nerida67 »

all mq/mks chassis are different with regards to engine mounting points between the different engines,not 100% sure if its the same with the gq model
maybe before handing over the $$$ slip down the local wreckers and measure a few and see wat the difference is
Top
Posts: 1836
Joined: Wed Aug 11, 2004 10:41 am
Location: Brisbane

Post by badger »

are the engine mounts 2 or 4 bolt? get the guy to measure where they are, also check the gearbox crossmember. if its a roller have a look at the diffs, if they have the small pinnion flanges and 4.3 or 4.6 ratios its a 2.8/3litre
1hd-fte 5 speed tiptronic 105 series
78 series troopy for work
gu ute play truck For sale
FTE 80 series sahara Sold

i think i have a problem
Top
Posts: 40
Joined: Wed Sep 05, 2007 2:56 pm
Location: BRISBANE

chassis

Post by choppedtrol »

yes the 2.8 and 4.2 are different engine mount positions one RHS. if putting a 4.2 into a 2.8 chassis the rhs mount has to be moved backwards but not totally sure how much. in the middle of doing this swap currently. we also have a rolling 4.2 cab and chassis 4 sale. rusted rear 1/4s and 1/4 windows but chassis good but missing the rhs mount as on the other chassis
GU ST 4.2TD UTE.
TRAY AND SLIDERS BY KUSTOM KAGES
Top
Posts: 57
Joined: Sat Nov 28, 2009 2:52 pm
Location: Gold Coast

Post by Turboshop »

How much do you want for the rolling chassis choppedtrol...?
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 1 guest