Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

80series vs 105series diffs.

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

80series vs 105series diffs.

Post by 80's_delirious »

I have an 80 series with factory lockers and a 105 series with open centres.

I would like to be able to use my toyota lockers in the 105series diffs. I know there are some diferences in the two diffs, but am not certain to what extent they are different.

Pros of 105s
slightly wider track width??
lower ratio 4.33 vs 4.1. 4.33 would suit my 35"s better
stronger dowels in the hub flanges

I would like to be able to remove and swap the factory locked third member or diff carrier into the 105.

Possible problems and questions I see are:-
I think the axles have different size splines or different spline count?
the factory diff locked diffs have one longer axle with longer splined section on it.
I will probably need custom axles to resolve these things. anyone know a rough cost of custom axles?
are crown wheel and pinion interchange-able?
will the 80 3rd member bolt into the 105 housing (minor mods OK)

Any specs or details on either would be great.

EDIT. sorry Ruff :oops: meant this to go in the Yota section, could a mod move it thx
Posts: 1768
Joined: Sun Mar 14, 2004 11:51 am
Location: Weipa

Post by crankycruiser »

the rears are a different spline count.

u cant swap CW&P as there is more or less bolts? that hold the 105 rear on. found this out as i was gunna sell a mate my old rear 4.8 out of my 80....

its not just stronger dowels in the 105 rear, they have 10mm studs as well..

EDIT: fixed stuff up :?
Last edited by crankycruiser on Tue Mar 16, 2010 9:36 pm, edited 1 time in total.
80 xtra cab
Supercharged LS1, Locked n shit

80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

Post by 80's_delirious »

crankycruiser wrote:the rears are different ratios.

u cant swap CW&P as there is more or less bolts? that hold the 105 rear on. found this out as i was gunna sell a mate my old rear 4.8 out of my 80....

its not just stronger dowels in the 105 rear, they have 10mm studs as well..
bugger. :x
Now I remember reading somewhere they have different number of bolts in the crown wheel. I knew about the studs too.
Posts: 1768
Joined: Sun Mar 14, 2004 11:51 am
Location: Weipa

Post by crankycruiser »

yer dunno how successful ya gunna be on this one :) that shoulda said rears are a differnt spline count too.... my bad :roll:
80 xtra cab
Supercharged LS1, Locked n shit

80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

Post by 80's_delirious »

crankycruiser wrote:yer dunno how successful ya gunna be on this one :) that shoulda said rears are a differnt spline count too.... my bad :roll:
do you know if the third member will bolt in to the housing?

I was thinking I might be able to have custom axles made, the more I think about it the better fitting airlockers sounds :?
Posts: 5714
Joined: Fri Nov 22, 2002 3:55 pm
Location: Perth WA.

Post by nicbeer »

hrmmm selling factory lockers.... :)
[url=http://www.outerlimits4x4.com/viewtopic.php?p=930942#930942&highlight=]Zook[/url]
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

Post by 80's_delirious »

nicbeer wrote:hrmmm selling factory lockers.... :)
yeah, could be an option, but freight to WA will cost you a bit :)
Posts: 5714
Joined: Fri Nov 22, 2002 3:55 pm
Location: Perth WA.

Post by nicbeer »

yeh and not wrong,

Ive been doing some searching and looks like i need the housings and not just the 3rd members.

if i am wrong and $$ is reasonable it may be an option.

Dont the 105s have factory lockers? or is more the $$ and already having the older diffs.
[url=http://www.outerlimits4x4.com/viewtopic.php?p=930942#930942&highlight=]Zook[/url]
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
Posts: 41
Joined: Sun Jun 14, 2009 12:36 pm
Location: BUNDY

Post by mickdirt »

I have a 100 series rear diff in my 80 I have a arb locker with 80 series star gears to fit the 80's axles, yes the 3rd member well fit in I had to do a very small amount of grinding to fit the crown wheel in other then that they pritty much the same. the 100 has bigger axles, hub dia and the bigger studs and dalws. so I think if you used the 80 therd member and axles and hubs they should go in to the 100 housing, just not sure about the brakes. both axles are the same lenght.. hope this helps in some way..
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

Post by 80's_delirious »

mickdirt wrote:I have a 100 series rear diff in my 80 I have a arb locker with 80 series star gears to fit the 80's axles, yes the 3rd member well fit in I had to do a very small amount of grinding to fit the crown wheel in other then that they pritty much the same. the 100 has bigger axles, hub dia and the bigger studs and dalws. so I think if you used the 80 therd member and axles and hubs they should go in to the 100 housing, just not sure about the brakes. both axles are the same lenght.. hope this helps in some way..
cheers Mickdirt,
can you clarify? you have a 100series third member in an 80series housing?

I did think of swapping the side gears to suit 100 series axles, but axles to suit the factory lockers are longer than standard on one side, and I would have to get side gears for a 100 series diff locked diff so they would have to come from toyota.

are the std 80 series axleas the same length as the 100s? I thought they were slightly different length?
Posts: 41
Joined: Sun Jun 14, 2009 12:36 pm
Location: BUNDY

Post by mickdirt »

I measured 80 and 100 axles and they they the same length, both only with lsd centers. I have my 80 series 3rd member with a 100 locker this was done to get the 4.3 diff gears, as 4.56 seam to not exist anymore..
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests