Notice: We request that you don't just set up a new account at this time if you are a previous user. If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Rhett wrote:It is four inch pipe I am using for the towers. I have alowed a fair bit of swing. the shocks are angled in more than the towers are at ride hite. so as it swings it straightens up in the tower. I was hoping to get shocks with a boot rather than a metal collar to give it that bit more room to beath as well.
does not look four inch in the pics ( as you are there I am happy to take you word for it ) .. greg has asked if you can send him some, to make a nice "bling" exhaust tip from
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
love_mud wrote: .. greg has asked if you can send him some, to make a nice "bling" exhaust tip from
I already have a 4" exhaust tip - pay attention Yug
That is 3 inches at very best ..
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
U two never stop. The tray is all primed up and ready to be painted. Got to do some welding on the fuel tank(move filler pipe. some pluming, front shock monts and I will be ready to roll again. And get a driver side CV before I forget its broken. Next comp will be at offroad expo at lcmp in the mud runs. We will see how the boggers go at 7000 rpm.
The tray is all primed up and ready to be painted. Got to do some welding on the fuel tank(move filler pipe. some pluming, front shock monts and I will be ready to roll again
All that work just to roll it again
Seriously is lookin cool though I hope to watch it at LCMP
Rhett wrote:U two never stop. The tray is all primed up and ready to be painted. Got to do some welding on the fuel tank(move filler pipe. some pluming, front shock monts and I will be ready to roll again. And get a driver side CV before I forget its broken. Next comp will be at offroad expo at lcmp in the mud runs. We will see how the boggers go at 7000 rpm.
At 7000rpm .. they will be working perfectly
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Not sure of the exaxt ofset but I think it is about two inches from the inside edge of the rim. I went for one quick burn on the black top and it seemed all right. I can't really tell till its driving again though.
Rhett wrote:Not sure of the exaxt ofset but I think it is about two inches from the inside edge of the rim. I went for one quick burn on the black top and it seemed all right. I can't really tell till its driving again though.
Cool, I meant whats it steer like in low aired down. Locked front??
I havent tried it yet I still have a busted CV in the front from when I had the 30s on. I will tell you when it is going. I was planning to take the welded front out and put a open center in till I got a air locker though.
Just put it up the ramp and run out of ramp. (its only bout a metre high.) Still had a heap of wieght on the tire though. took some phots but I can't get my camera to work so yous will have to wait. Tray is all painted up yellow and black and the front shock towers are welded in.
Rhett wrote:Just put it up the ramp and run out of ramp. (its only bout a metre high.) Still had a heap of wieght on the tire though. took some phots but I can't get my camera to work so yous will have to wait. Tray is all painted up yellow and black and the front shock towers are welded in.
will be good to see some pic's ..
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
The Local paper took some picys of my rig today. (not for the police report thankgoodness) They wanted to know a bit about Q rock. I flexed it the most I ever have for the photo. Got the back wheel up on five palets. I will scan my picy up when it is printed. Next thursday I think. I have my insurance form and nomination form filled out for expo too. Hoping to C a few of the outerlimits spooks there.
Rhett wrote:The Local paper took some picys of my rig today. (not for the police report thankgoodness) They wanted to know a bit about Q rock. I flexed it the most I ever have for the photo. Got the back wheel up on five palets. I will scan my picy up when it is printed. Next thursday I think. I have my insurance form and nomination form filled out for expo too. Hoping to C a few of the outerlimits spooks there.
cool mate, was gonna enter my shitbox in production class, but dont have a letter from qld transport about the bodylift. i might be up to spot anyway, should be good
wHEN FLEXING I did notiice I will have to do some triming of the front guards. Would there be any reason why the drivers sides rubbs well before the passenger side? Other than it is a bit sagged.?
camo- Im running in the front: ulitimate rears, 2" droped hangers and extended shackles. In the rear: Extended drop shakles and 2" lifted king springs. Sprung over all round and all over load leaves removed and a few others swaped about. munro shocks all round, Camira in back and tritans in front I think.
Any way the back has been cut as all U know but with another roll over under my belt and the front end not looking real happy am I going to bush the front end for tube? or replace pannels and trim front guards of couse for full travel and 37s.
Well it is baCK Ive been and rolled and fixed again. But some Questions. Do all 1 litre bonnets hit on radiator cap in the 1.3 or is it cous I used a morti bonnet? Is the bonnet latch different for a morti? my old one don't fit.
Some quetions of different nature. What is better droop or tuck? The suzi I have pics off in the thread earlyer Matts is almost up to the suspension stage tube and body are finished. He s found a set off 44s for it and I don't think it will have much room for tuck just droop. And will his gears be low engough series 3 rh and 4 somethings 45 series LC diffs?
) .. greg has asked if you can send him some, to make a nice "bling" exhaust tip from 
