Does anyone have some tips on how to disassemble Tigerz11 winch motor and brake from the end plate? Is the motor a interference fit with the end plate? They are kind of setup like the one in this ad.
http://www.ebay.com.au/itm/NEW-12V-Winc ... 937wt_1139
I want to pull it all apart so I can drill and tap the housings for air fittings to feed them low pressure compressed air.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
How to disassemble Tigerz11 winch motor
Moderators: toaddog, TWISTY, V8Patrol, Moderators
How to disassemble Tigerz11 winch motor
The Silver Bullet - BJ74
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Re: How to disassemble Tigerz11 winch motor
I had been thinking about doing the same thing with mine,
What are you using to regulate the low pressure air.
I was thinking about only putting about 10kPa, that will keep the water out down to about 1m under water.
What are you using to regulate the low pressure air.
I was thinking about only putting about 10kPa, that will keep the water out down to about 1m under water.
05 Manual HDJ100R
84 HJ60 w/12HT, twin locked with longfields
84 HJ60 w/12HT, twin locked with longfields
Re: How to disassemble Tigerz11 winch motor
Just going to use a regulator down to 5psi to pump into the casing.
The Silver Bullet - BJ74
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Re: How to disassemble Tigerz11 winch motor
Hey Hulsty,
Mate I think what you need to do is undo the tie rods and remove both the drum support plate and motor in one piece from the winch. On the inside of the drum support plate are some allen head bolts which will allow you to remove the drum support from the motor. This is the process for the gearbox side so I don't think it's going to be much different for the motor side.
Give me a call if you need a hand.
cheers
Dan
Mate I think what you need to do is undo the tie rods and remove both the drum support plate and motor in one piece from the winch. On the inside of the drum support plate are some allen head bolts which will allow you to remove the drum support from the motor. This is the process for the gearbox side so I don't think it's going to be much different for the motor side.
Give me a call if you need a hand.
cheers
Dan
Work - KPD4X4.COM - KPD Industries Australian Distributor of Diesel Power Modules - Germany.
Play - dank's zook
Play - dank's zook
Re: How to disassemble Tigerz11 winch motor
thanks Dan will give that a go!
The Silver Bullet - BJ74
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Who is online
Users browsing this forum: No registered users and 4 guests