Allied competition beadlock wheel 17in

[YEA 13B]

Has anyone fitted tyres to the allied steel competition beadlock wheel 17in? I need some first hand advice? Not 2nd or 3rd hand or my mates mate has them.

http://www.alliedwheels.com.au/?page_id=62" onclick="window.open(this.href);return false;

Anyone who has fitted tyres to them your help would be appriciated.

[flexytj]

they loose the inner bead at low psi . you would be better off spending extra on a walker evans rather than being disappointed with the savannah .

[YEA 13B]

they loose the inner bead at low psi . you would be better off spending extra on a walker evans rather than being disappointed with the savannah .

You obviously didnt even read my post where i said STEEL wheels. savannah's are ALLOY.

[SIM79]

Whats the issue?

I had never fitted a beadlock before and found it very easy, just time consuming.

[MikeH]

put the rim on a 20 litre drum so the tyre can hang down evenly.
Once you get all the bolts started do them to 10Nm in a cross pattern, then 15, then to 20.

If you have trouble getting them started buy half a dozen longer bolts or some bits of threaded rod and nuts to get things going then once you get the surrounding bolts in change them back to the normal bolts.

retorque the locking bolts regularly, depending on the tyre then can bed in a bit.

[YEA 13B]

put the rim on a 20 litre drum so the tyre can hang down evenly.
Once you get all the bolts started do them to 10Nm in a cross pattern, then 15, then to 20.

If you have trouble getting them started buy half a dozen longer bolts or some bits of threaded rod and nuts to get things going then once you get the surrounding bolts in change them back to the normal bolts.

retorque the locking bolts regularly, depending on the tyre then can bed in a bit.

Yes ive done exactly that, but there is an uneven gap between the inner and outer ring? All other beadlocks i have used tighten down so they touch. And what valves did you use?

[SIM79]

put the rim on a 20 litre drum so the tyre can hang down evenly.
Once you get all the bolts started do them to 10Nm in a cross pattern, then 15, then to 20.

If you have trouble getting them started buy half a dozen longer bolts or some bits of threaded rod and nuts to get things going then once you get the surrounding bolts in change them back to the normal bolts.

retorque the locking bolts regularly, depending on the tyre then can bed in a bit.

Yes ive done exactly that, but there is an uneven gap between the inner and outer ring? All other beadlocks i have used tighten down so they touch. And what valves did you use?

I'd start again, something isn't right.

Do they have a built in coning ring?

[flexytj]

put the rim on a 20 litre drum so the tyre can hang down evenly.
Once you get all the bolts started do them to 10Nm in a cross pattern, then 15, then to 20.

If you have trouble getting them started buy half a dozen longer bolts or some bits of threaded rod and nuts to get things going then once you get the surrounding bolts in change them back to the normal bolts.

retorque the locking bolts regularly, depending on the tyre then can bed in a bit.

Yes ive done exactly that, but there is an uneven gap between the inner and outer ring? All other beadlocks i have used tighten down so they touch. And what valves did you use?

what tyres are you using ?

[Shieldsy]

Buy some stauns

[MikeH]

maybe your tyres are dodgy...

Staun needs to make a dual regulator fill rig so you can air up and down and maintain the correct pressure differential. Without that I wouldn't bother with them.

[YEA 13B]

Brand new 40" trepador's. All rims are doing the same.